KitchenAid Parts

This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are most often used to light the inside of refrigerators and ranges. It features a standard socket base, which means you simply unscrew the burnt-out bulb and screw in the replacement. Depending on the appliance you may require a screwdriver or nut driver to access the light bulb. We recommend you wear work gloves while handling this replacement part. It is constructed of glass and metal and is sold individually. Depending on the appliance and location of the bulb within it, you may want to consider disconnecting power and using a flashlight for easier access to unscrewing and re-screwing in your bulb during this repair.

This OEM gray Dishwasher Lower Dishrack Wheel Assembly is a plastic kit that allows the rack to slide in and out of the dishwasher easily. If it breaks or becomes damaged. sliding will feel difficult. This can happen due to normal wear and tear, and the part should be replaced if this occurs. Check your model number and user manual to make sure this part is correct. It attaches directly to the dishrack. To repair, open the dishwasher door and pull out the lower dishrack. Next, push the tab from both sides and it should pop out. To install the new wheel assembly, place it on the rack and make sure the caps overlap the wire from the inside before you clip it in place by pushing the wheel. It measures roughly 3x6 inches.

The lower door closing cam is used in refrigerator doors, it can be located on the fresh food side or the freezer side. It helps hold the door open. This cam is made out of plastic, so it might crack or wear down over time. If your door will not open and close properly you may need to replace the door closing cam. To successfully install this part, you will need a 5/16 nut driver and a small flat blade screwdriver. Before you begin, unplug your appliance and disconnect the water supply. Lubricating this part may help with installation. This replacement part is sold individually. This part will fit both the left and right side of your refrigerator door. To make the repair, remove the top hinge cover, then the top hinge support. Lift the door from the bottom support and remove the old door cams. Replace the cams, using a little lubricant if necessary, and place the door back on the lower hinge support. Replace the top hinge support and your repair is complete!

Sold individually. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward.

This OEM Dishwasher Upper Rack Adjuster is a grayish-black, plastic part which will require a screwdriver to install. It fits onto dishwasher rack and connects it to the track allowing it to slide in and out. If broken then the rack will no longer slide properly, and the part must be replaced. The installation has been rated as "easy" by customers. Before beginning any repair, you should unplug the dishwasher and wear gloves to protect your hands. Check your model number and user manual to see if this part is right for you! Your dishwasher should have a left and right upper rack adjuster, and both are the same part. These parts are sold individually, so if you are looking to replace both, you will need to order two parts. Please see as follows for detailed repair instructions: Release the track stops from the upper dishrack rails and pull the upper rack from the dishwasher and place it upside down on a work surface. Raise the wheels to the maximum height. Release the top of the long rear clip from the dishrack tine and push the clip down to the release point and remove it. Press the tab down on the front clip move the clip up to pull it off. Release the locking tabs on the clip in the middle of the height adjuster and remove the clip. Using a slot screwdriver pry the housing cover down and out to release the upper tabs on each side. Pry the bottom of the housing cover out of the 2 lower locking tabs. Pull the housing cover off the rack. Remove the adjuster housing and wheel assembly and repeat the procedure on the other side. Slide the vertical portion on the new wheel assembly between the fourth set of vertical tines from the back of the dishrack and rotate the wheel assembly so that it lays flat against the side. Insert a positioner clip above the rear wheel and snap the tab into the slot. Install a positioner clip on the front wheel. Position the adjuster body over the vertical portion of the wheel assembly and push in into the slots. Locking tabs at the bottom of the adjuster body engage the wheel assembly once it is fully inserted the tabs. Insert the actuator lever into the adjuster body with the thumb pad facing the front of the rack. Two half-circle cutouts on the adjuster body hold the actuator in place. Push the adjuster body down and install the adjuster cover. Install the adjuster cover mounting screws. Repeat this process on the other side of the rack. Push the upper dishrack onto its tracks.

The door balance kit helps support the dishwasher door. This kit includes 2 door balance links and 2 door balance mounts with wheels.

18ml

This part chops up/mince the food particles to prevent from clogging the dishwasher pump. This is a chopper assembly or drain food chopper, and it is designed for your dishwasher. The chopper chops up/minces the food particles in your dishwasher to prevent them from clogging the pump. You may need to replace this part if your dishes are not being cleaned properly, your appliance is particularly noisy, or you are noticing draining problems. The tools you will need to make this repair include a number 20 and a number 15 torque screwdriver, a small flat blade screwdriver, and a pair of needle nose pliers.

The Door Cam is a black plastic part which helps the door pivot shut while keeping the door and hinge in proper alignment. Lubricating this part upon installation may help it move easier. It attaches onto the door hinge and should be replaced if broken or if there is noticeable damage. Refer to your model number and user manual to ensure this is the correct part for you. To do this repair you will need a 5/6 nut driver, a 5/16 socket, and a ratchet. For safety purposes, do not forget to turn off your appliance before making this repair. Note that this piece is black, and as per the manufacturer requires a new screw to mount the door cam which is sold individually. Please also note that this is the closing cam for the lower door, and the upper door cam is sold as a separate kit.

This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer.