This advanced refrigerator water filter utilizes Triple Filtration Technology to reduce a wide range of contaminants, including mercury, lead, and trace pharmaceuticals, ensuring cleaner and safer water for drinking and food preparation. Certified to meet NSF standards, it is designed to deliver high-quality filtration performance across ...Read morecompatible refrigerator models. The filter should be replaced every six months or after filtering approximately 300 gallons to maintain optimal contaminant reduction. A noticeable decrease in water flow from the dispenser may also indicate the need for replacement. Installation is quick and tool-free, and it is recommended to flush at least two gallons of water through the system before use.
The lower door closing cam is used in refrigerator doors, it can be located on the fresh food side or the freezer side. It helps hold the door open. This cam is made out of plastic, so it might crack or wear down over time. If your door will not open and close properly you may need to replace the door closing cam. To successfully install ...Read morethis part, you will need a 5/16 nut driver and a small flat blade screwdriver. Before you begin, unplug your appliance and disconnect the water supply. Lubricating this part may help with installation. This replacement part is sold individually. This part will fit both the left and right side of your refrigerator door. To make the repair, remove the top hinge cover, then the top hinge support. Lift the door from the bottom support and remove the old door cams. Replace the cams, using a little lubricant if necessary, and place the door back on the lower hinge support. Replace the top hinge support and your repair is complete!
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, and freezers. This is a genuine OEM part and includes a brush applicator. Please remember to wear gloves to protect your hands when applying this paint.
This icemaker can be used with 25-27 cubic feet refrigerators that have a vertical auger dispenser located on the freezer door. Reuse bottom bracket from the original icemaker and attach to the new.
This twenty-five watt microwave light bulb is two and a half inches long. It has a small, screw-in base and it carries 120V. This item sells in a quantity of one, though many microwaves require two.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
3
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Cynthia - For model number KSCS25INSS01
February 9, 2020
How many cubic feet
Hello and thank you for writing.
This unit is 24.5 Cu. Ft.capacity. We hope this helps. Please contact us anytime if you require further assistance.
2 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
JOANNE - For model number KSCS25INSS01
August 22, 2023
I cannot remove the water filter below the freezer on my side by side refrigerator. The old cap broke and the I am unable to attach the new cap to the cartridge still in the refrigerator. I have tried turning the cap every way but it will not line up so I cannot remove the old cartridge to replace it. This is the first time this happened, I have replaced the cartridge many times in the past. Hope you can help. I even watched the video. No luck still. Thank you.
Hi Joanne, thank you for contacting us. First, you may need to make sure you have pressed the water filter button on the left side of the cap before removing the filter. To install the new cap, you just have to give it a little clockwise turn, and it locks in place. If you are still unable to remove the filter, then you may need to check the filter housing, part number PS11748616, as it is most likely faulty. We hope this is helpful!
Hi Nancy, thank you for reaching out. Based on our research, your model has approximately the following dimensions:
Height: 71 1/2 inches.
Width: 35 11/16 inches.
Depth: 30 1/8 inches.
We hope this information helps!
1 personfound this instruction helpful.
Was this helpful?
Thank you for voting!
Patrin Ogwaro - For model number KSCS25INSS01
March 25, 2026
Seeking common issues for this model or similar common issue ..compressor tests ok with continuity . Compressor doesn't run ,continues to clicks on and off and so on . I didn't find the typical comp starter relay , any clue what out of many things might be the problem?
Hello Patrin, thank you for contacting us. If your compressor has continuity, the inverter box is likely faulty and unable to convert power to start the motor. We would recommend replacing it to fix the issue. The part number is PS8760019. We hope this solves your problem!
I tried to replace the light bulbs inside the refrigerator but it doesn’t work. Is there a special type for this model. I don’t have the manual on it!
Hello Mary, thank you for reaching out to us. You will need to check the light socket, part number PS371236. Overheating or loose wiring can burn out the socket. Look for burned spots, rust, or loose connections. If the socket is fine the issue could be with the door switch, part number PS12728638. Press it manually with the door open to see if the light flashes. If it feels stuck, clean it with electrical cleaner. We hope this information helps!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
No ice
567 of 688 peoplefound this instruction helpful.
Daniel from Suwanee, GA
Easy
15 - 30 mins
Screw drivers, Socket set
removed flap door in front of icemaker...removed 3 screws with bolt heads...removed one additional screw with bolt head and ice unit slid out. I removed motor unit (pops out no screws). Replaced and had ice within 3 hours.
Was this helpful?
Thank you for voting!
there were directions
754 of 1282 peoplefound this instruction helpful.
Kate from Jacksonville, FL
Very Difficult
30 - 60 mins
We didn't know where the product went and it was very difficult to install.
Was this helpful?
Thank you for voting!
Ice maker stopped functioning
463 of 495 peoplefound this instruction helpful.
Phil from Auberry, CA
A Bit Difficult
15 - 30 mins
Nutdriver, Screw drivers
Remove the icemaker service door... gently pry the door pins from the hinge sockets. Remove the 3 screws from the under side of the icemaker with a nut driver (1/4"). Gently remove the icemaker . It's a tight fit between the top of the compartment and the icemaker lower support tray. Next, disconnect the electrical connector at the ri
... Read moreght side. You're done! Reverse procedure for installing. Good luck. Remember, your working with cold plastic...take your time and don't force too much.
My Orders
