LG Parts

Washing Machine Drain Pump

★★★★★

★★★★★

58 Reviews

The drain pump and motor assembly may also be known as the washer drain pump and is a part for your washer. The drain pump helps expel water from the washing machine. The drain pump is activated after the spin cycle speed is maintained for a specific period of time. To make this installation you will need a Phillips screwdriver, a small flat-blade screwdriver, a pair of needle-nose pliers, and a pair of slip-joint pliers. Note that the pump casing is not included. This medium-difficulty repair may vary, but can generally be started by disconnecting power, then removing the top of the washer by taking out the four back screws and two small brackets. Then, remove the front panel by taking out the two screws and eight tabs that should be taken from the top. Moving down the front of the washer, remove the door, latch, tub gasket, and drain cover. Disconnect the drain hoses and clip from under the drain assembly, and install new assembly from there. Reassemble parts in direct reverse order -- taking photos during disassembly and keeping parts clearly organized can help here. Despite the number of steps, you will only need a standard Phillips screwdriver to complete this repair.

Dryer Lint Filter

★★★★★

★★★★★

21 Reviews

The Dryer's Lint Filter is used to collect lint during the dryer cycle as it passes through the dryer vent, in order to prevent damage to the machine. This manufacturer-approved part comes in gray, measures around 12 inches wide by 11 inches high, and is easy to install. It slides into the lint filter slot in your dryer. If there is visible damage to the screen then it's time to replace the part. We recommend that you thoroughly clean the lint filter before every load, but even with good maintenance, this hard-working part is often damaged or worn over time. If your dryer isn't drying quickly, the filter may be responsible. The manufacturer has made an authorized substitution to the lint filter. Special details: When replacing lint screen ADQ56656401 you may need to also replace lint screen housing MCK49049101 and lint screen guide MEA49050001 to prevent items from catching on the lint screen, depending on your model.

PARTS ASSEMBLY, SVC (2 Pack)

★★★★★

★★★★★

1 Review

The drum roller for your dryer holds the drum in place while the drum turns on the support wheels. The drum roller is round with a bearing in the middle and measures approximately 3 inches in diameter. Over time, these rollers can become worn, and it may cause your dryer to be noisy during operation. The bearing inside this roller is self-lubricating, so no grease will be required.

Refrigerator Water Filter

★★★★★

★★★★★

2 Reviews

This refrigerator water filter replacement is for 2010 LG refrigerators that have either forward French doors or are the four-door dispensing models. This filter is designed to minimize impurities that can cause ill-tasting water or an unpleasant smell. It reduces sediment, dirt, rust, limescale, sand, and many other contaminants that can be harmful to your health and the life of your appliance. This filter should be replaced every 6 months or 200 gallons to ensure top quality performance. To remove your unwanted filter, press the push button to open the filter cover (water may spill from the hole), pull out the old cartridge in a downward motion. To install the new filter, make it so the ears are in the horizontal position and push the new cartridge into the housing until it stops. Push the filter upward until it is secure. Click the cover to lock it in place. Run water for approximately 5 minutes to prep the filter for use, and discard water. Reset the “filter reset” button if applicable.

Dryer Drum Belt

★★★★★

★★★★★

3 Reviews

This belt helps rotate from the drive motor to the drum.

Refrigerator Door Switch

★★★★★

★★★★★

1 Review

This door switch is used in refrigerators. It is activated by the closing and opening of the door

Dryer Lint Filter Assembly

★★★★★

★★★★★

4 Reviews

The lint filter sits in your dryer, and collects loose lint when the machine is operating. Sometimes the lint filter will become clogged or damaged, and in this case, you will need to replace your current lint filter with this part. The frame of this line filter is made of white plastic, and the filter is sold individually. To replace the filter, simply remove the old, damaged filter, and replace it with the new one.

Water Inlet Valve - Hot

★★★★★

★★★★★

12 Reviews

Moisture Sensor

★★★★★

★★★★★

2 Reviews

Water Filter This filter is good for 300 gallons and it reduces chlorine, taste and odor, sediment and rust. Sold individually.