If your fridge doors aren’t sealing properly or you’re noticing cold air escaping, this front plate assembly might be the fix. Also called a mullion or flipper, it fits between the French doors to keep the cold in and your food fresh. Made for select LG and Kenmore models, it’s built from sturdy plastic and helps your fridge run more efficiently. Just check your model number to make sure it’s the right fit.
This refrigerator water filter replacement is for 2010 LG refrigerators that have either forward French doors or are the four-door dispensing models. This filter is designed to minimize impurities that can cause ill-tasting water or an unpleasant smell. It reduces sediment, dirt, rust, limescale, sand, and many other contaminants that can...Read more be harmful to your health and the life of your appliance. This filter should be replaced every 6 months or 200 gallons to ensure top quality performance.
To remove your unwanted filter, press the push button to open the filter cover (water may spill from the hole), pull out the old cartridge in a downward motion. To install the new filter, make it so the ears are in the horizontal position and push the new cartridge into the housing until it stops. Push the filter upward until it is secure. Click the cover to lock it in place. Run water for approximately 5 minutes to prep the filter for use, and discard water. Reset the “filter reset” button if applicable.
This handle screw, also known as a mounting bolt, is a mounting screw to help secure the door handle to your refrigerator door. If your handle is loose, you may just need to tighten the screw. If your screw is missing or broken, it may need to be replaced. There are multiple handle screws on your fridge, please consider ordering extra as ...Read morethey commonly wear at the same rate. This is about 1 inch long and metallic in color.
This is the replacement shelf glass for your refrigerator. It is made of glass and is approximately 31 inches wide and 16 inches long. The shelf glass for your refrigerator slides over the crisper cover and acts as a sort of lid. It also creates a shelf that you can place food and beverages on. If your current shelf insert glass is broken...Read more, this part is the appropriate replacement. Many of our customers have described this repair as easy. To complete the repair, carefully remove the old glass from the frame and replace it with the new pane of glass. This part is sold individually and is an authentic OEM part.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
John - For model number LFX28968ST
June 6, 2023
I would like to know what wattage my Refrigerator requires to run. I am trying to figure out what generator I need for my home. Could you please advise at your earliest. Thank you.
Hi John, thank you for reaching out. According to our research, your model requires 120 Volts and 15 Amps, or 1800 watts to run. We hope this helps!
2 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Mike - For model number LFX28968ST
December 2, 2021
Hi there, I need to purchase the ice maker assembly but I’m having a hard time finding the right one. I don’t need the auger assembly, just the ice making part. Can you guide me into the right direction?
Hello Mike, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number: PS7788168. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Hello Margaret, thank you for reaching out. According to our research on the model, the problem appears to be with the Defrost Sensor Assembly, part number PS3636324. Customer service is available 7 days a week if you need help placing an order. We hope this helps!
Hello Cathy, thank you for contacting us. The most probable cause of the issue is a faulty ice bin assembly, part number PS7789317. It stores the ice until needed and comes with an auger that rotates to move the ice into the dispenser chute. We would also recommend inspecting the micro switch, part number PS3529276. It controls dispensing of ice or water when you press the dispenser lever. Customer service is always available to help you place an order if you are having trouble doing so. Good luck with your repair.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
replace leaking water inlet valve assembly
42 of 75 peoplefound this instruction helpful.
Richard from JACKSONVILLE, FL
Really Easy
15 - 30 mins
Screw drivers
1. Shut off water to refrigerator. 2. Removed bottom sheet metal cover (6 screws). 3. Removed leaking water inlet valve assembly from refrigerator (1 screw). 4. Remove water inlet tube (loosen nut) and tube back to refrigerator (pull from water valve after remove cotter pin washer). 5. Detach two electrical wire harnesses. 6. Install new
... Read morewater inlet valve assembly to refrigerator (1 screw). 7. Replace both water tubes to water inlet assembly. 8. Re-attach both wiring harnesses. 9. Turn water to refrigerator on. 10. Check for leaks. 11. Re-attach bottom sheet cover (6 screws).
Read less
Was this helpful?
Thank you for voting!
Remove and replace light switch
45 of 91 peoplefound this instruction helpful.
Debbie from Waltham, MA
A Bit Difficult
30 - 60 mins
Pliers, Screw drivers
Video makes it look easy. Kenmore refrigerator does not have "groove" along the right hand side of switch that allows for pushing down on release. Used a thin screwdriver to get under to push while holding switch edge with pliers. Kept slipping. Tape sides to avoid scratching inside of refrigerator.
Was this helpful?
Thank you for voting!
The factory door gasket was split and needed replacing
22 of 36 peoplefound this instruction helpful.
Carl from LAKE WYLIE, SC
Very Easy
Less than 15 mins
I pulled the gasket off and installed the new one. It was very easy. All I had to do was to push the new gasket in place in the grooves in the door. The gasket I received was identical to the one I replaced.