Inglis Parts

Dryer Repair Kit

★★★★★

★★★★★

125 Reviews

The Whirlpool Dryer Repair Kit includes a belt, drum rollers, an idler pulley, clips, and a washer to resolve noise and drum issues in 27-inch dryers. Compatible with Whirlpool, Kenmore, Maytag, and more, it installs easily with standard tools after disconnecting power.

Refrigerator Center Crisper Drawer Slide Rail - White

★★★★★

★★★★★

207 Reviews

Rack Track Stop

★★★★★

★★★★★

60 Reviews

The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes properly, the rack stop may need to be replaced. The replacement part may differ slightly from the broken part, depending on the model. However, the different styles are interchangeable. This product is sold individually and comes in both a white and grey plastic version. Many of our customers found this repair to be very easy and takes less than 30 minutes to complete. Simply snap the old part out and snap the new part into place. You will not require any tools to complete the job. This is an authentic part approved by the manufacturer.

Multi Rib Belt - 92-1/4"

★★★★★

★★★★★

136 Reviews

This dryer drum belt has four ridges, three grooves and is 1/4" wide.

Dryer Thermal Fuse

★★★★★

★★★★★

106 Reviews

Maintenance Kit

★★★★★

★★★★★

77 Reviews

The drum support roller kit (Dryer Repair Kit) allows the dryer to tumble properly by supporting the drum cylinder. The idler pulley provides the tension required for a multi-ribbed belt. The belt attaches to the drum, idler pulley, and motor pulley. If your dryer is damaged, it may be making loud, squeaking, and/or squealing noises while the drum is turning. This is from normal wear and tear. The drum may eventually stop turning all together. This is a sign the part should be replaced. This is one complete maintenance kit. The kit includes the drum belt, drum support rollers, one idler pulley, four tri-rings, and one clip. The parts are constructed of plastic, metal, and rubber, and come in black/white/silver.

Dryer Drum Support Roller

★★★★★

★★★★★

12 Reviews

This drum support roller is sold individually. Most dryers require two. The tri-rings are included. This is a drum support roller for a dryer. It is a genuine replacement part. This part is sold separately. Most dryers require two drum rollers. It is recommended to check and replace both drum support rollers at the same time to ensure proper drum rotation and because they often wear at the same rate. The drum support roller holds the drum in the proper position while it spins on the support wheels. If rollers are worn out, they will cause the dryer to be noisy.

Agitator Directional Cogs

★★★★★

★★★★★

135 Reviews

These agitator directional cogs are commonly referred to as dog ears. They come four to a package and are usually used with direct drive washing machines.

Heating Element - 5300W Includes the insulators and restring already attached. This dryer heating element produces heat to dry clothes in a dryer and is located in the rear end. If the heater element is burned, dryer does not heat or over heats, or clothes take too long to dry, then replacing this part could solve your problem. The tools needed for this repair project are: Phillips screwdriver, putty knife, needle nose pliers. To repair, first remove the main top of dryer and remove ground strap at the rear. Next, disconnect two wire harnesses that hold front panel to the cabinet to pull out front panel. Once you have access to the inside of the dryer, refer to the manual for further installation instruction. As a safety precaution, remember to unplug appliance from power source before beginning this repair project.

Light Bulb - 40W

★★★★★

★★★★★

60 Reviews

This 40w light bulb is a replacement bulb constructed of glass and metal. It is an easy-to-install electrical part which produces 40w of light. If the bulb won't light up then it may be broken and should be replaced. The bulb attaches directly to an appropriate light socket and has a small screw-in base. To access the exterior light bulb, you will need to remove the panel on the bottom of the microwave using a Phillips screwdriver. If your exterior light bulb has not been changed before, it is probably held in place with some silicone. You will need to cut away this silicone to remove the old bulb. If you cannot access the silicone with a utility knife, it can be removed using dental floss. Once the silicone is removed, simply unscrew the old bulb, and replace it with the new one. Be sure to disconnect the power to the microwave before you begin this repair. This light bulb measures about 1 1/8 inches. We do not recommend using a higher-wattage bulb for this appliance, and can only recommend this specific bulb. If fixing the bulb does not solve your microwave light issue, it's possibly a problem with the socket, which means the socket and/or board will need to be replaced. This can be a more dangerous repair, so consult your user manual or a technician before attempting.