Chop Saw Parts

This genuine DeWalt replacement power cord is built for durability and long-lasting performance, featuring a thick outer rubber insulation that stands up to demanding job site conditions. Designed for double-insulated tools, it includes two wires and two prongs, eliminating the need for a ground wire. The cord measures 10 feet in length and uses heavy-duty 14-gauge wiring, making it ideal for tools that require a robust power connection. This part replaces obsolete part #875692 and is sold individually. Installation involves connecting the bare wire ends to the appropriate terminals and ensuring the cord is routed correctly to prevent pinching when reassembling the tool’s housing. For best results, refer to your tool’s manual or consult a qualified technician.

This switch activator button is a genuine Makita replacement part, It is sold individually. It has to be pressed to activate the power switch. This is a very common replacement part. It is advised to order one or two extra to keep on hand. This Makita switch button is compatible with the tools listed below, and it is not guaranteed to fit any other power tool models.

Reduce friction and extend tool life with this genuine manufacturer-sourced ball bearing. Made of durable metal, this high-quality replacement part is designed for use with a variety of equipment from trusted brands. Ball bearings play a critical role in minimizing friction between rotating parts—distributing weight evenly and allowing components to spin smoothly. This helps reduce wear, improve efficiency, and ensure long-lasting performance. Bearings are subject to constant pressure, heat, vibration, and friction during operation, which means they may require periodic maintenance or replacement. This part is sold individually and is also included in part number 395843-00. For proper installation and compatibility, refer to your equipment’s diagram or manual.

This is a genuine OEM replacement part which is sold individually. It is always best to replace both brushes, even if only one is worn. Brush Holder and a Brush Cap are sold separately. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

It is a genuine OEM sourced replacement part that is specially designed for Ryobi cut-off saws. This is the rubber pad for the base of the cut off saw, it helps to support it and reduce vibrations while in operation. It is made with durable rubber material and it is sold individually.

Genuine OEM Dewalt replacement Carbon Brush and Holder Assembly. This brush comes complete with carbon brush, spring, and holder. Most brush replacement jobs will require the purchase of two of these brush assemblies. Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

This is a manufacturer sourced replacement part designed for use with Makita power tools. It helps to secure the brush in the housing. This screw-in cap is made of hard plastic and it is sold individually and measures 7-18 HM 1500. To replace it you would need a flat-head screwdriver.

This part is available as an individual replacement part. The magnet sleeve goes between the stop ring and the wave washer. It is made of plastic and will require replacing if it becomes broken. A screwdriver may be needed when replacing the sleeve. This genuine item is supplied by the original equipment manufacturer for use with Makita sanders, grinders, trimmers, and jigsaws.

This is an authentic Ridgid item, not an aftermarket imitation. It is sourced from original equipment manufacturer for use on circular saws and sanders. The purpose of a washer is to distribute the pressure evenly between two connected parts. For correct use and location of this washer please make sure to check appropriate diagrams. This part is made from durable metal and it is sold individually.