Average Repair Rating: 4.2 / 5.0, 4 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Water leaking at front left of washer especially after heavy loads
Disconnected water and unplugged. Took off top and control panel. Replaced water inlet valve with new one. Simple plug and play connections. It was easy to see the old valve was bad with rust and sediment collecting on hot side.
Other Parts Used:
Kynrick from DENTON, TX
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
7 of 8 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water was dripping while the machine wasn’t running
Removed two screws that held the control panel from the back with a power drill. Pop the control panel loose with a screwdriver from the top of the machine with the quick disconnects. After turning both the hot and cold water off I remove the hoses with pliers removed two screws with the power drill that hold the water inlet valve in place disconnected the wire harness plug And removed water inlet valve swap, the original harness to the new water inlet valve and follow the steps backwards to finish
Other Parts Used:
Brian from VESTAL, NY
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
4 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer not filling then timing out before load done
Turned off power and water. Removed hoses/Unplugged power. Removed screws to open and access control panel. Removed existing valve first by pinching off 6 wire connectors then screws securing valve to washer base. At this point, I replaced with new valve and reattached everything. I also added screen washers to both hoses as I suspect it was built up debris in original valve impeding water flow through valve that led to problem…
Other Parts Used:
James from RICHMOND, VA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
no water to washer
a couple of issues to get valve out and off , 15 min. install and top back on!!!
Other Parts Used:
Donald from LINN CREEK, MO
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Socket set
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
19 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Charles
November 16, 2019
Washer seems to go through all the correct sequences until it try’s to fill with water. You can hear it trying to get water in but it’s very faint water running sound and it clicks randomly in the area of the water fill valve solenoids. Is the water fill solenoid my problem or is it the circuit board?
For model number 110.26132411
Hi Charles, the water inlet valve is the most likely fix. Thank you for your question and good luck with your repair!
7 people found this helpful.
Was this helpful?
Thank you for voting!
Leon
June 4, 2019
I have Whirlpool cabrio washer model number wtw7300dw1 cannot get water to come in can it's be the water inlet valve
For model number WTW7300DW1
Hi Leon, thank you for your question. Yes, you should take a look at your water inlet valve.The valve can be tested with a multi meter and should be reading between 500 - 1500 ohms of resistance. Good luck with your repair.
5 people found this helpful.
Was this helpful?
Thank you for voting!
Robert
November 12, 2019
I stripped the threads on the cold water inlet, would this replace that piece?
Hello Robert, thank you for contacting us, In order for us to locate the correct parts and repair information we will require the model number of the unit. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. Look forward to hearing from you!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Robert
November 13, 2019
I stripped the threads on the cold water inlet, will #14 in this diagram replace that? If not where can i find the part i need
For model number WTW7040DW1
Hello Robert, thank you for your question. Yes, the item # 14 valve PartSelect Number: PS12349461 is the correct replacement part for this unit. Good luck with your repair!
3 people found this helpful.
Was this helpful?
Thank you for voting!
AJ
June 22, 2022
When the washer begins a normal cycle it sounds like there is water hammer. A plumber came and installed two pressure valves to reduce the noise but it still continues to make a banging noise. When the normal wash setting is on cold, the machine calls for Hot water and while holding the pipe i can feel it making a banging sound every few seconds. Would replacing the inlet valve solve the problem? Thank you!
For model number WTW7300DW1
Hello AJ, Thank you for your inquiry. If the washer is already set to be getting only between 30-55 PSI for water pressure (which is the usual cause of water hammer), we would recommend checking the water inlet valve, the water pressure hose and the control board as this controls the flow of water coming into the washer. Check the hose and test the water inlet valve with a multimeter, and if replacing the valve does not fix the issue, you may have a faulty control board. We hope this helps and if you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
My inlet valve strainers are plugged with filter sand. Can I remove strainers and clean them. The strainers are not easily removed - at least in my case.
For model number WTW8127LC
Hello David, thank you for contacting us. Yes, you can remove these filters from the inlet valve using needle nose pliers and insert them again after cleaning them. We hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Richard
April 2, 2022
i am trying to find a part number for inlet water valve assy W10758829 rubber seats( 3 ea ).on the bottom of module. been looking for quite a while. T hats the assy number
For model number whirlpool Cabrio washer water inlet module
Hi Richard,
Thank you for your question. Before we can provide you with information on the water inlet valve, we will need the model number from your washer. We have included a link from our website that you may use to find the model number on it. If you could resubmit your question with this information, we would be happy to help you. We are open 7 days a week. We look forward to hearing from you!
Does Water inlet valve-#W11220230 come with filters? I don't see them sold seperately.-Thank you
For model number 110.26132412
Hello Russell, thank you for contacting us. Yes, the water inlet valve you mentioned comes with the filters. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Lois
October 12, 2023
Can I remove the filter screens on part W11220230 if I need to clean them? If so, how is this done without crushing them?
For model number MVW6230HW0
Hello Lois, thank you for reaching out. We have attached a relevant video to help you remove and clean the water inlet valve filter screen. This video may not be of exact part but will help you with the process. Glad to be of assistance!
Was this helpful?
Thank you for voting!
Samantha
December 13, 2021
our hot water valve is stuck open on our whirlpool cabrio washer. Is this the correct part to repair this?
For model number wtw7000dw1
Hello Samantha, Thank you for your inquiry. We have researched your model and confirm that this is the correct water inlet valve for your model. We hope this helps.
Was this helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
