Get in touch, we're here to help!
1-866-883-8386
Monday to Saturday
8am - 8pm EST
Product Description
Suspension Rod Kit Specifications
These rods help keep your washer drum steady during cycles, so it doesn’t shake or bang around. If your washer is noisy or feels unstable, the suspension rods might be worn out. This kit includes all four rods (about 27 inches long) and the parts needed to secure them. You’ll need a few basic tools to install them—like a screwdriver and wrench—and a bit of disassembly is required. It’s a genuine part made to fit your machine.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Shaking and Moving | Spinning Issues
This part works with the following products:
Washer.
This part works with the following products:
Whirlpool, Maytag, Kenmore, Crosley.
Part# W11130359 replaces these:
W10594082, W10785954, W10821704, W10901060, W11027215, W11033536, W11226784
Customer Reviews
Filter By Rating:
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Karl S - December 12, 2025
Verified Purchase
Easy repair straight swap out
Appears to be original equipment. So far works well. Totally eliminated the washer spin shake problem and banging. An easy fix for the spin error lockout - took about an hour.
Stefano F - September 27, 2023
Verified Purchase
Easy repair works like new very good quality parts
Very good part and service my washer works like a new one
Olivier D - August 2, 2024
Verified Purchase
Replace suspension
Up to now, it perfect repair. Hope it will last longer than the original.
Etienne L - August 20, 2024
Verified Purchase
BUY THESE, DON'T GO CHEAP
Long story short : My Whirlpool washer started banging very loudly, so I looked for replacement parts. I found some on Amazon for half the price, installed them, and for 2 weeks, it didn't bang. Then, the banging started again quickly. I thought the problem was the transmission bearings, so I bought a new transmission, but that didn’t work. I then replaced the stator motor, which also didn’t solve the problem. After spending $650, I came back here to buy the original suspension, which cost $50 more, and the washer stopped banging. It’s been 2 months, and I haven’t had any issues. The quality part bought here fixed the problem—forget Amazon!
- < Prev
- 1
- Next >
Customer Repair Stories
Average Repair Rating: 4.0 / 5.0, 2 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Out of balance code , shaking during spin cycle
Removed three screws on back to open top panel, used small vice grip to pull on suspension rod to unhook and remove from the drum. Remove and replaced one at a time so the rods keep drum suspended and prevent from dropping in the cabinet . Reinstalled top panel and done .Very easy completed in about 20 minutes.
Other Parts Used:
-
Gregory from Seminole, FL
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replaced the suspension springs
The video was excellent in what needed to be accomplished. However it showed reaching inside the tub with vise grips to grab the old spring. This worked fine for removing them but the installation of the new spring did not allow my hand and vise grip to secure the new spring and pull it up and insert it into the retainer. I found that by taking a cord and putting it through the socket and retainer allowed me to pull straight up and seat it in the retainer a lot easier.
Other Parts Used:
-
Dave from EUSTIS, FL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS12347544
Manufacturer Part Number: W11130359
Manufacturer Part Number: W11130359
Brand
Model Number
Description
Get in touch, we're here to help!
1-866-883-8386
Monday to Saturday
8am - 8pm EST