1108873279A Kenmore Washer Dryer Combo - Instructions

Removed the drum then removed the old parts and installed the new ones. Dryer now runs very quite and heats good. You have very fast service my mother ordered the parts on the net one day and I received the parts next day and did the repair that night and dried clothes. Thanks,

Your great service is very hard to find.

first of all, the parts i ordered arrived THE NEXT DAY, which is fantastic. and all for under a hundred bucks. secondly, the parts came with excellently detailed instructions that included photos, so the repair itself was pretty easy. i opened up the washer, disconnected 2 hoses, slid the entire tub/motor assembly out as directed, loosened the nuts holding the old suspension springs in place, removed the old tub spring, lifted the tub off the old suspension springs, removed and replaced the springs with new ones, and put everything back together again. tub is tight, spin cycle is nearly silent...it's like a new machine. the only reason the repair took as long as it did was because i took the opportunity to clean everything out in there--about a decade worth of grime and dust. cleaned the hoses, cleaned up the tub, cleaned under everything. this is my second repair with partselect (the dryer half of my machine went bad last month), and the second time the repair has gone flawlessly. i couldn't be happier.

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

Attributed excessive noise to age of dryer, upon closer inspection, a dish towel had become caught at rear of drum because the drum support rollers were damaged causing the drum to create a space in the rear of the drum. This was large enough for the dish towel to be caught. Originally I thought that the thermal fuse had blown the circuit-which should occur in an overheating situation-however the loose drum had worn through the electrical wire leading to the door switch because it was not properly seated on the rear drum rollers. the wire was repaired with a wire nut, rear drum rollers were installed and it is working again. thank you for the extremely fast shipping

Took of the btm pan and the top to be able to remove the front. Raised the drum enough to replace the right hand wheel. ( the old ones had already been removed) Replace the left hand wheel and bracket. Re assemble the machine. Worst part was trying to do all this with the can of beer in one hand!!

I watched the part select you tube video that links specific loud dryer noises to specific broken or loose parts. It allowed me to identify the part I needed, which I ordered through their website. Two days later, I had the part and installed it, with help from another online video that showed me how to take the dryer apart to install the drum support roller. Thank you, the information provided made the repair quite easy. It works perfectly now!

I replaced a bad thermostat

Watched the videos for the repairs on the site. Took the back of the dryer off after unplugging the appliance. Removed the failed fuse and thermostat and replaced them both per the video steps. It took about 25 minutes for both parts and the dryer now works well.

I just changed for the new one! 2 seconds.

Simply put it in the exhaust hole.

very smooth with your video instruction help

Lifted top of dryer using putty knife. Took front panel off using socket wrench. Slipped drum belt off an took drum out. Vacuumed out entire interior. Replaced rollers an clips and reassembled!! Saved $100!!! Thank you!!

Repair was not successful

Top up, front off. Drew a picture of how the belt was positioned. Removed the belt and drum. Removed a heat plate to access the lower wheel. Replaced it and then replaced the upper right wheel. Was a little concerned the white triangular washers would break going on to the shafts but it turned out there much stronger that I thought. Cleaned out the bottom and found a lot of coins. Put it back together and now it sounds like a new dryer. Use gloves, some parts inside are very sharp.

Replaced drum support rollers but did not fix problem. Motor was fried! Replaced with used motor. NOTE. Make certain you install motor in the right position or you will find the drum sitting on motor. The guide must be in the 4 o.clock position and then placed in bottom groove for proper alignment of motor to drum. Job was amazingly easy and online instructions were super helpful.