1108873279A Kenmore Washer Dryer Combo - Instructions

The tough part was replacing the front cabinet.
I did consult the video for help on replacing the clutch spring.
Thank you for that bit.

I admit to taking too much apart, most of the cabinet back can be left alone.
Some of the plastic wire keepers/routers suffered, as well as the console hinges.

The newly reassembled washer works without a hitch, and truely it took me about 4 hours over several days to dissamble and reassemble.
It is louder in the audible range than before, but very serviceale for another 20 years, saints willing.

I called a repairman, who diagnosed the problem as a faulty leaf switch in the lid assembly -- the little rod on the lid that normally would depress the switch was working fine, but the switch was not closing. At my direction, he bridged the wires from the switch as a test, and it worked fine. So I ordered a new switch from you guys and swapped the new one out with the old one. Two flat screws to remove the slanted top panel, and at the rear of the panel are two hex-top screws holding the lid assembly on. Undo the hex-top screws, lift off the lid assembly, unplug the interlock between the washing machine power and the lid, and find a clean place to lay the lid assembly. Replacing the switch is a snap -- the part you sold came with its own wiring, and all it takes is take the old part out and put the new part in. Easy peasy. Getting the lid assembly back takes a little work because the fasteners are a little tricky to position correctly -- they will fall off the lid assembly and repositioning them may involve a bit of trial and error -- but once it is properly positioned, it takes a total of six screws and you're done. Two for the switch (Philips), two hex heads to fasten the lid assembly to the washer chassis, two to button up the front access panel.. A caution -- make sure the machine is unplugged when you do the repair, or else the washing machine may cycle into a spin cycle when you plug the interface back in and surprise you.

DO NOT WATCH THE INSTALLATION VIDEO ON WEBSITE! It's a nice video- just put me through a lot of grief because it did not apply to my washer. It is not necessary to open the control panel to pull out something at the bottom of the timer shaft(that isn't there)...or anything else requiring tools. Just UNSCREW the knob, and pull up on the old dial to remove it. Then line up the large tab on the new dial with the large cutout on shaft, and press it on. Then screw the knob back on. That's it. Finished. 5 minutes with correct instructions.

Removed old assemblies manually and replaced with new. Very easy and the parts fit perfectly!

remove the front panel, belt [notice the way the belt is fasten] remove the tub, support bracket to the drum roller, and slide the new drum roller on and place the tre ring in the slot. then re-install everything in reverse

Popped out the old lent trap & popped in the new one..and walla perfect repair..

Replacement fit perfectly.

I followed the instructions on the video and it was simple. The hardest part was vacuuming out 32 years of lint from around the motor and igniter. I was lucky there was never a fire in the dryer.

Didn't need a repairman for this project! Ordered the part (seems like on Sunday) and got it really quick (the next Wednesday). Opened the package, placed the part where it was supposed to go and shazam!!!! Fixed it was quick and easy!

I would not ever consider this a repair. The dryer filter cracked because of my wife put it in loosely. The new one just fit right in.
What was so good about the entire process was how quickly I recieved the part. A matter of two days.

Excellent and super easy. Owned the box and snapped the new one in. Ready for laundry again in a matter of minutes.

Easy for a 87 year old.I just snapped the cover to the filter basket and then inserted the whole basket into the

When i finally got sick and tired of hearing it when she used the dryer. I popped the top flipped it up unscrewed the 2 screws holding the front panel of the body on, picked up on it and pulled it off the drum. I then reached back to the rear right corner and stretched the tentioner and pulled the belt off the motor pulley.Then I picked up the belt and the drum and pulled it out of the dryer body. After seeing the drum support roller that is mounted on the base, and back of the left side I decided to go online and find this sight that had the drum support rollers as a set with the keepers and the push nut for the brace as a set for a really fair price. If your unit has a warranty "do not" take anything apart and do not order any pats until you check with your dealer. You do not want to void your warranty. I then pulled off the push nut and then i took the screw that held on the brace in front of the worn out drum roller, then pryed off the keeper and pull off the drum roller, took off the back keeper;inspect the shaft if it is not damaged ,(this one was not),then you wait until the parts arrive, yes your dryer will set in parts for about a week, but believe me in todays economy its worth "not having to buy a new dryer" at least for this small repair. When the parts arrive everything is pretty much in reverse of how you took it apart dont forget your cell phone is also a camera that can be a "memory enhancer" for when you get this far. Also be nice to your wife your going to need a little help putting it back together. Of course if she wants her dryer back she needs to help anyways. patience is a virtue and if you dont take your time and do this right it will be tested the drum and belt need to be fitted right and held up to get both the belt on the pulley and around the tentioner and get the front panel lined up on the front of the drum good luck and pass your knowledge on its getting to be a lost art.

I pried open the top of the dryer, removed the 2 scrws holding the front cover of the dryer, un hooked the dryer drum buide belt, removed the dryer drum - all this just to get to the drum support roller. The bottom roller - the rubber on the wheel had been "chewed of". I can only guess because too much weight was placed in the dryer with wet clothes.
I removed the triangle shaped retaining clip, using the mini flat head screw-driver, slid the damaged roller off, replaced the new roller, and installed the new retaining clip. To install the new clip, I used a 1/2inch nut driver. I did the same to replace the upper drum support roller. The actual repair took less than 5 minutes, However, the prep time in dismanteling the dryer in order to get to the drumm rollers and puting the dryer back to gether consumed the bulk of my time.

1. Popped off hinged dryer lid at front and supported to allow access to lint chute
2. Removed back sheet metal panel
3. Removed dryer chute to expose sensor; removed same-deformed terminal on top needs to be straightened with pliers to remove through slot.
4. Installed new sensor; terminal needs to be twisted to ensure solid installation and good ground. Bottom pops in but took a bit of finagling.

Accessing and replacing the sensor was straightforward enough; bulk of the job was cleaning off old gasket material (severely degraded) in two locations. Used plastic scraper and razor blade scraper, then cleaned sticky with goo gone. Installed new gasket strip from Home Depot; available in rolls. I used 1/4" x 3/8". Surprising how much lint/hair/debris was in bottom of lint chute. Glad to get it all clean.