1108873279A Kenmore Washer Dryer Combo - Instructions

popped open top, removed two springs on lower end of front panel.took off same panel, pulled drum forward, pulled jesus clips from roller pins ,took off old rollers and replaced with new rollers and clips.

Take out the two screws the hold the lint screen filter compartment in place. Remove the two top clip retaining screws, and lift the top LOOSE and turn it a bit out of the way. I didn't find it necessary to remove the top. Unclip the two wire electrical connector at the top - front, and remove the 1/4 " screws the secure the front. Lift the front up and out of the way. Slide the drum belt off the tensioner and moter pulley and slide the drum out the front. Remove and install the rollers ( and its just that quick) and while your in there. Clean up a bit ... cant hurt right? Especially on and around the motor. Reverse the procedure but rotate the drum a few turns to properly position the belt. Total E.T. is maybe 20 minutes and on a 1 - 10 scale for "degree of difficulty ". This is about a 2. Save the money and do it yourself.

Pull out lint filter and remove the two philips head screws.....Then use a flat screwdriver to gently pry loose the top front corners of the dryer.

After safely securing the top in an upright postion.....disconnected the door switch....then remove the two 5/16 inch metal screws holding the front of the dryer on.

Once screws are removed.... gently lift the entire front of the dryer...up and off of the unit.....exposing the dryer drum assembly.

By releasing the tension on the drum belt "idler pully... you can then remove the belt from the pulley on the electric motor.....and then move the complete drum assembly straight forward and out of the machine...through the opening provided ( There is an area that has been "cut out" of the metal...especially for this procedure)

Once drum assemby is out of the way.....all that is required....to change the support rollers...is to pry off the plastic retainer "clips" ( Triangle shaped) and slide the rollers off of the shafts.

Although the original rollers had not originally been lubricated in any way , at the factory ( Possibly the reason for the premature failure)....I decided to apply a coating of lithium grease to the shafts and inside of the rollers, prior to re-assembly.

Once rollers were installed and retainer clips in place.....re-assembly was accomplished by "reverse order" of the teardown procedure.

After unit was re-assembled...it ran quieter than it ever has!

Used repair video as guideline, I did not have their lab conditions to work in and by no means a clean machine. Also I had a two part front panel vs. single as in video, so disassembly and reassembly were OJT."on job training". Video was however very usefull in locating problem, getting correct part and accomplishing the repair. Saved $$ and machine is now working properly again. Am saving this web-site to my favorites list.

part fit perfect

I simply removed the damaged lint filter and replaced it with the new one I purchased. It took less than 30 seconds to do.

always unplug from outlet first, unscrewed the back off and pull off the wire from cycling thermostat ,take the two screw out that holding it in place and replace the new one .Very simple and easy. Thank you for the easy step by step video to complete this repair. James

wasnt a repair but a replace

I replace the terminal block, wires , and dryer plug I unscrewed the back of the dryer and basically replace was burnt out. I was about to pay 200.00 to have it done but I looked on youtube and seen how easy it was so I just chose the site to order what I needed to be replace and it arrived quickly and more affordable to do it myself. Thanks I hope the was useful.

Stuck it in, done. The really good thing was your website - the BEST I've ever used to order anything on the web, bar none. SO clear, SO organized, SO logical, SO easy to use. I just wish other companies using the internet to sell things would learn from you guys. Kudos to you and your webmaster, really outstanding.

Took the back off the dryer. Disconnected the old thermostat and installed the new thermostat. Connected the back of dryer. Put in a load of clothes to dry and the clothes were dry on the first try. Works like a new dryer. Saved a lot of money not having to buy a new dryer when all I had to do was replace some old parts.

layed the dryer door side down, took 6 nuts off back metal panel, then took the bolt off at bottom and reached in and pulled drum support rod loose, removed old roller, installed new roller, reached in set drum support rod back into hole where the threads were showing on the outside where the nut was then put back on and tightened back up, put a pair of vicegrips underneath on rod to hold in place while tightening up nut,placed cover panel back on with screws and now it works like a new one, runs very quiet. Cost was 25 dollars for part nothing to do it ourselves. We priced new dryers that size they're well over 400 dollars. Easy REpair!!

Replaced it

Neither the washer or the dryer of the stacked unit would start. The website suggested that one of the causes could be the thermostat. I ordered a replacement that arrived quickly. Swapping the part only took minutes, and it started just fine.

Ordered new rollers from PartSelect. I followed the video to replace the rollers. Everything went well. The video did not show how to put the belt back on. I then went to replace broken belt and there was the way to go through the pulley. Works great with no noise. Just like new. Thank you