41729 - Instructions

Replaced drain pump following easy to follow video. Also replaced circulation pump at same time, as it is connected to common sump housing and only added a few more minutes to repairs.

Use a cup to take the water out of the washer. Get at least three large towels -- you're going to have to sop up the water when you disconnect the hoses.

Take the bottom panel off (2 Phillips head screws). Drain pump is on the right side.

Remove the two screws holding the pump to the metal bottom plate. Use a small socket wrench and/or a screwdriver. I had to use a screwdriver on the right screw and a socket wrench on the left screw! Place as many towels in the cavity as you can to catch the water that's going to come out when you detach the hoses.

There is an inlet hose and an outlet hose, attached with bright green clamps. Remove those with pliers. Clean up the water that drains out. The hose in the back (inlet) has a "coin catcher" area. Clean this out.

Attach the hoses to the new pump. Screw it down. Replace the bottom panel.

drum vane had a hole in it replaced it using phillips screwdriver removed one screw ,pulled drum vane towards the door then pulled up replaced it reversing the procedure. It actually seemed to fix my leak during spin cycle

Watched instructional video. Made it easy

Just aligned and pushed in.

The hardest part was figuring out how to get the lid off. You simply remove two screws from the back of the lid and jerk and slide the lid towards the back of the machine. Take out the screws that hold the front panel on, tilt the front out and access the lock/switch assembly and replace.

I followed the steps outlined on (several) web sites detailing the replacement process. Just Google " LG front load washer won't drain". A couple of small quirks cropped up that required some adaptations such as: I had to purchase an automotive hose clamp to reinstall the main tub drain hose to the pump manifold. I couldn't get the oem clamp back on. It kept slipping out to the jaws of my pliers and I don't own a pair of those clamp pliers that make the job easy. Also, the hex head/phillips screws used to attach the front panel to the frame were very tightly installed AND they had their heads rounded off! I didn't have the hand strength to make the phillips screwdriver loosen them so I used a pair of vise grips to carefully start the process and used the phillips to finish. Finally, the wire loop used to retain the big gasket that seals the front had door is tricky to reinstall. It took two people to get it right. All in all , the videos make the job pretty routine.

Using a cordless drill and driver bit I removed the back cover, bottom front cover and top. I then removed the rubber bellowed hose connecting the soap dispenser to the rubber boot in front. This one was tricky to reinstall because the fastener for the hose is twisted steel wire that needs to be undone when reinstalling. It slid off easily enough but would not slide back on easily. There is a second small bellowed hose that connects the dispenser to the outer drum casing. This needs to be removed as well. It comes off easily and went back on easily. I used a one sided razor to cut the glue dots connecting the front boot to the washer door frame. After that I removed the belt from the motor and drum pulley by hand and then removed the motor mounting bolts using a ratchet and socket. This went smoothly. I now propped up the drum using 4x4 cutoff blocks to take the weight off the springs and shocks. I then removed to the lower upper plastic pins that hold the shock onto the plastic spin drum casing. I used a wooded block and a hammer to tap the pins out. Be sure to push in the lock on the tapered end of pin shaft. The second pin was a little more difficult to remove and required quite a bit of tapping to push it all the way through. I tried adjusting the weight on the shocks several times to make it easier to come out. The pin was slightly damaged by the time I got it out from hitting it. It went back in OK so I don't think the damage will cause any problems. Next I got someone to help lift the drum to release the weight on the springs and removed then from the top end. You need to remove the spring clamps that hold the spring down at the top end. I used a wrench to remove the bolt that holds the pullet on the drum shaft. The pulley was easy to pry off shaft by placing two flat screw drivers between the shaft and the bearing casing and twisting the screw drivers. Once the pulley was removed I turned the spin drum casing upside down and supported the outer casing with two stacks of 4x4 cutoff blocks. This would allow the stainless steel drum to be supported above the floor and drop freely as the shaft worked it way out of the bearing casing. Getting the drum shaft out of the outer housing bearing was the most difficult part of this whole process. The shaft was rusty and therefore did not easily slide through the two bearing casings. Before hitting the drum shaft to remove it from the bearing casing I put the washer and bolt back on the shaft to protect the shaft from hammer/mallet damage. I tried a mallet but it only moved the shaft part way and then it wouldn't slide further. I then used a 1/2" steel pipe cutoff as a punch seated around the pulley bolt to alloy me to use a hammer to beat the shaft out of the bearing casing. It required a tremendous amount of force to move the shaft. Once the shaft was removed from the old drum casing I spent some time cleaning the back of the stainless steel drum including using emery cloth to remove the rust from the shaft and polish it the best I could. Be sure not to damage the brass bushing that the rubber bearing seal rides on to prevent water leakage. Once the drum and shaft were cleaned up the reassembly process when smoothly I simply reassembled the washer in the reverse order or the disassembly. The shaft went into the new bearings snugly which I was pleased to see since the snug fit meant that the water would be sealed in and the drum would spin true. The hardest part was reattaching the large bellowed hose onto the soap dispenser because it require undoing the twisted steel wire clamp and getting it back together in a very tight space. I use a combination of a flat screw driving and a needle nose pliers to wrestle it back together. The finished job resulted in a very quiet smoothly operating washer which we expect will give us another 5 years of service.

Removed (1) philips screw in toward back of vane (closest to rear of drum), pulled the vane forward to remove it, slid the new one in place, replaced the screw, and was done in less than two minutes. Piece of cake.

Used a shop vac to suck all the water through the drain hose. Removed the bottom front panel held by two screws on bottom and two plastic pins at the top. Removed electric connector on front of pump. Removed two screws holding pump down. Used pliers to move spring clips back so hoses could be removed. Put hoses on new pump and squeezed clamps with pliers to pull them back over the hose connection. The connection on the left was a little bit of a pain due to space limitations. Screwed the new pump down and reconnected the electric plug. Put the bottom cover back on and screwed it into place.

I released the door gasket and unscrewed the unit .Labeled the connections. then reconnected reattached, then put gasket back on. Worked like a charm!

First I turned off the water. Since the pump is at the front of the machine,it was easy to get too. I then removed the hoses by squeezing the hose clamps with pliers. I removed the electrical plug and then removed the 3 screws holding the pump to the base. I changed orientation of the outlets per instructions,which was very easy. Installation of the new pump was performed in reverse. I had difficulty getting one of the hose clamps back on and changed it to a screw clamp. I turned the water on,ran the machine and checked for leaks. Partselect saved me several hundred dollars in repair costs.

Had a puddle on the floor under the washing machine. While I couldn't definitively confirm the source of the leak, I suspect it was the drain pump. As such, I replaced the drain pump and the drain hoses (one of those 'while you're in there' things). The toughest part of the whole job was moving the washer away from the wall. I was able to leave the water hoses connected and just unplugged the electrical cord. Watched the YouTube video regarding the replacement and it was exactly what I needed. Just take your time and make sure everything fits together without force. In addition to the pump and the hoses, I had some drum shocks that I had previously purchased, but never installed. Replaced them at the same time. Everything fit together as expected and the washer works great. No leaks and reduced vibration. Good for another 15 years - hopefully.

Removed entire tub assembly, replaced bearings and seal in rear outer tub assembly, had spider arms welded by aluminum welder. alot of work ,saved 150.00 on parts by replacing bearings, savings untold hundreds by doing it myself instead of replare man.. BIG JOB. But just plug away and it goes rather smoothly.

Pulled out the old plunger and inserted new one. Just have to make sure the tabs align with the slots.