Whirlpool WP40111201 - Multi Rib Belt | PartSelect.ca
Multi Rib Belt – Part Number: WP40111201
( Grid squares measure 1x1 inch )
Multi Rib Belt – Part Number: WP40111201 https://partselectca.azureedge.net/Schematics/Maytag/58910.gif

Multi Rib Belt

Your Price

CAD$19.61

PartSelect Number PS11742271
Manufacturer Part Number WP40111201
Manufactured by Whirlpool

This dryer drum belt from Amana has five ridges and is 93-3/8" inches in length, and 3/8 of an inch wide. It is flat, black in color, and is made entirely of rubber.

This part works with the following brands: Amana, Speed Queen, Maytag, Crosley, Magic Chef, Admiral.

This part works with the following products: Dryer.

This part fixes the following symptoms: Will not tumble | Noisy | Takes too long to dry | Will Not Start

Videos For installing this part.

Questions & Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".

Customer Repair Stories

Average Repair Rating: 3.0 / 5.0, 112 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Robert from Skokie, IL
Difficulty Level:
Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver
Parts Used:
WP40111201
Replace drive belt
Remove front panel, lint basket, motor mounts,exhaust hood, front drum brackets. Then slip serpentine belt around drum, pressure w/ tension idler pulley and slip around drive motor spindle. Replace all parts in reverse order (a two person job).
Vacuumed inside of dryer (full of lint.)
293 of 337 people found this instruction helpful.
Was this instruction helpful to you?
David from Underwood, IA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Parts Used:
WPY54414, WP40113601, WP40111201, WP37001298, WP37001042, WP23748, 12002090, WP500121, WP233520
Loud banging sound. Worn out roller.
Pulled off the lower panel with 5/16 socket.Pulled off the door assembly by removing the two screws at the bottom of the door assembly. I pulled down a little and then out. be carefull of the wires. Other posts said to remove. The wires were long enough I did not have to remove them. I just leaned it against the wall. I then removed the 4 screws that hold the front piece in.pulled it off replaced brackets , installed self adhesive felt(stuck good) and then glides. Mine were thin but not the problem. I then reached under the drum and released the belt from the tensioner. I then pulled the whole drum out.This is the time to vacum out good. I could get to the rear rollers very easy. The left roller was shot and the shaft half wore into(the problem). I pulled off the two screws holding the roller support. Normally You have to remove the wheel with snap ring pliers first to remove the support. In this case snap ring long gone. Replaced support shaft, installed thrust washers and roller with grease for both sides. The right support shaft was still good. Removed tensioner pulley and inspected. It was just as good as the new one. Cleaned and greased and reinstalled. Put new belt on the tub and slid it back in. Be carefull to get the belt on the proper side of the tensioner. I then installed the front supprt in place to support the tub with the 4 screws. Spun the tub(felt good) then reached under and reinstalled belt to motor and tensioner. Spun again to check for belt alignment. (Check) Reinstalled door an lower panel. Test Quiet Sounds like new. Very easy! I hope this helps someone just as the other post has helped me. Blessings to all.
157 of 227 people found this instruction helpful.
Was this instruction helpful to you?
john from Blue Springs, MO
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers, Socket set
Parts Used:
WPY54414, WP40111201, WP37001042, 22001300, 203956
Washer on spin cycle would shake, rattle, and roll. Walking accross the floor.
Damper kit and Springs corrected the problem. Follow the instrutions listed on this web site and all went well..The only problem was with the damper kit. The "kit" did not include the glue needed to replace the damper pads. This cost a delay on a day and trip to a local parts store that I did not want to make. So be sure to order glue for the damper pads.
56 of 65 people found this instruction helpful.
Was this instruction helpful to you?
russell from anamosa, IA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Socket set, Wrench set
Parts Used:
WPW10116735, WP61623, WP503979, WP40113801, WP40111201, WP37001298, WP37001287
would run but would not heat
removed front cover and top took drum out remove heating unit replced limit switch and fuse reinstalled installed new idler put new belt around drum installed drum replaced glides put top back on and front cover . then replaced boosting heater witch is on the blower also cycling thermostat
46 of 1300 people found this instruction helpful.
Was this instruction helpful to you?
JOHN from CORPUS CHRISTI, TX
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Parts Used:
WP37001042, WP233520, WP40113601, WP40111201, WP23748
Dryer would squeal when drying clothes
Unplugged dryer, turned off gas, raised front of dryer with two 2X4's on edge resting on legs, removed two lower panel screws, removed lower panel. Removed lower blower & filter assembly, screws (3) are on the inside of drum. (Good chance to clean it out) Removed two lower front upper main panel screws. Supported top panel with wood for access. Removed panel slowly, marked wires that go to door switch, set panel aside. Removed tension on belt by reaching in on the right lower side and unhooking the tensioner from belt, look to see how it is installed, for reinstallation on assembly. Pulled drum out slowly as not to damage seals on drum. replaced parts, attached with self tapping screws.(screws all the same size) reassembly in reverse order. Will need to put belt on drum before installing drum. Check drum alignment with rollers and seals. Used very small amount of high pressure grease on roller bracket and shaft assembly where the support roller shaft spins for lubrication. All's quiet. (Vacuumed out inside while dissassembled)
35 of 41 people found this instruction helpful.
Was this instruction helpful to you?
Robyn from Pullallup, WA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Socket set
Parts Used:
WP37001287, WP37001042, WP2200376, WP40111201
Screaming noise and drum not turning
Removed top, remove front panel, removed drum assembly brace, removed drum and belt . The belt and rotor were shot. I replaced both drum support rollers since i was there. Then replaced the motor and Idler lever and pulley, the put the belt on and put everything back. This unit will last a while longer and the grand total including next day air 175.00. I tried to just by the motor locally but for 242.00 I got every thing listed above.
Thanks
29 of 35 people found this instruction helpful.
Was this instruction helpful to you?
Dann from Claremont, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Parts Used:
WP40111201, WP37001132
Drum Not spinning
First, I unplugged the dryer. Then I used a flat screw driver to pop the top open. I removed 2 bolts from the front cover and removed the front door cover. I also took pictures of the electrical connector on the door so I would remember how the wires went back on. Then I removed 4 bolts from the front drum guide and lint screen holder. This allowed me to remove the drum & old belt. While the drum was out, I pried an access panel open on the side of the dryer. I then glued the new back felt piece in place. I put the new belt around the drum and re installed it. I re-installed the front guide and front cover re-connecting the door electrical switch. With the access panel open, I attached the belt to the motor. I then plugged it back in and turned it on to verify operation pryor to snapping the top cover back in place. Very easy repair.
24 of 28 people found this instruction helpful.
Was this instruction helpful to you?
Garrett from Racine, WI
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Parts Used:
WP40111201
Original belt finally gave way.....(15yrs old)
Simply remove the front panel screws(2) at the bottom of the dryer. Pull bottom of panel outward until it swings free of the top(taking care not to pull the wires out). Rotate out of the way and remove the two left side screws holding the drum plate and snake the belt around the flange. Reinstall those screws and remove the same ones on the right side. Snake the belt behind that flange and reinstall screws. Then all you have to do is run the belt around the motor sheave and the idler pully and your done. Reinstall the front panel.
23 of 24 people found this instruction helpful.
Was this instruction helpful to you?
Dan from Newfield, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers, Socket set, Wrench set
Parts Used:
WPY54414, WP40111201, WP37001144, WP23748, WP233520
Dryer wouldn't rotate the drum.
Removed the screws holding the bottom to the sides (but after taking it all apart, I think I could have done the repair by just taking the front off :-(.
Removed the screws holding the front to the sides. Noted the wiring (three wires go to the front door switch). Removed the wires from the switch (they are quick connects, so no tools necessary). Removed the front. Pull the drum out.
Disconnected the spring from the idler pulley lever. Removed the bolt and nut holding the idler pulley lever assembly to the bottom. (The old pulley had basically frozen in place which caused the belt to break). Put the new washers, wheel assembly and retaining ring on the new idler pulley lever. Bolted it back in place. Connected the spring. Put the new belt around the drum and slid the drum into place. Put the belt around the motor pulley and past the idler wheel (make sure it is on the correct side so this takes up the tension). Put the bottom screws back in. Connected the wires back up to the front. Put the front in place. (Make sure that the drum is properly seated in back so the front goes on and the drum will turn). Put the front screws back on.
21 of 605 people found this instruction helpful.
Was this instruction helpful to you?
John from Litchfield, NH
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set, Wrench set
Parts Used:
WP500121, WP37001298, WP37001287, W10856845, WP40111201
Idler Pully Squelling
Squeling from inside dryer. To Fix-
Pry dryer top cover off by popping cover off the two fastening clips located at about 3" inward from the two front corners. A screw driver at these two locations is easily inserted between the top cover and front panel.
Next remove the two screws on the top inside of the driver approximate size 5/16 inch. Pull the top of the front panel outward and then note how the lower portion clips into the fram, lift the front panel off the clips and roll it to the right. Remove the 4 screws and bulkhead.
Draw a picture of how the belt wraps around the drum and idler. Also note the belt orienation on the drum. Roll the belt off the idler pully and reomve the drum.
Replaced Idler asembly by first removing the tension spring and lastly the retaining bolt.
Reinstall everything in reverse order. Can be a bit tough getting the belt around the idler and motor pulley however this is managable. My machine runs great now!
Once again Parts Select comes through with great delivery, perfect fit, good pricing, accurate parts list. This is my third purchase and I have been 100% pleased. By far the best on line service I have ever experienced.
19 of 31 people found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
19 Reviews
4.8
out of 5
Filter By Rating:
  • 5 Stars
    16
  • 4 Stars
    2
  • 3 Stars
    1
  • 2 Stars
    0
  • 1 Stars
    0
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".

Model Cross Reference

Brand
Model Number
Description
Amana
7493-LEM437
Dryer - DRYER
Admiral
ADE7005AKW
Dryer - Residential
Admiral
ADE7005AYW
Dryer - Residential
Admiral
ADE9005AGW
Dryer - Residential
Admiral
ADG7005AWW
Dryer - Residential
Speed Queen
AE3213
Dryer - Residential
Speed Queen
AE3413
Dryer - Residential, Electric
Speed Queen
AE4113
Dryer - Residential
Speed Queen
AE4213
Dryer - Residential
Speed Queen
AE4413
Dryer - Residential, Electric
Speed Queen
AE5113
Dryer - Residential
Speed Queen
AE5213
Dryer - Residential
Speed Queen
AE5413
Dryer - Residential, Electric
Speed Queen
AE7133
Dryer - Residential
Speed Queen
AE7233
Dryer - Residential
Speed Queen
AE9133
Dryer - Residential
Speed Queen
AE9233
Dryer - Residential
Speed Queen
AE9433
Dryer - Residential, Electric
Speed Queen
AEE933
Dryer - Residential, Electric
Speed Queen
AEE953
Dryer - Residential, Electric
Speed Queen
AEM197
Dryer - Residential, Automatic
Speed Queen
AEM333
Dryer - Residential, Electric
Speed Queen
AEM353
Dryer - Residential, Electric
Speed Queen
AEM377
Dryer - Residential, Automatic
Speed Queen
AEM397
Dryer - Residential, Automatic
Speed Queen
AEM407L
Dryer - Residential, Automatic
Amana
AEM407L2
Dryer
Speed Queen
AEM407L2-PAEM402L2
Dryer - Speed Queen Dryer Model AEM407L2-PAEM402L2 (AEM407L2PAEM402L2, AEM407L2 PAEM402L2) Parts
Speed Queen
AEM407W
Dryer - Residential, Automatic
Amana
AEM407W2
Dryer