Jenn-Air Dishwasher Dishracks

Dishwasher Upper Rack Adjuster

★★★★★

★★★★★

140 Reviews

This OEM Dishwasher Upper Rack Adjuster is a grayish-black, plastic part which will require a screwdriver to install. It fits onto dishwasher rack and connects it to the track allowing it to slide in and out. If broken then the rack will no longer slide properly, and the part must be replaced. The installation has been rated as "easy" by customers. Before beginning any repair, you should unplug the dishwasher and wear gloves to protect your hands. Check your model number and user manual to see if this part is right for you! Your dishwasher should have a left and right upper rack adjuster, and both are the same part. These parts are sold individually, so if you are looking to replace both, you will need to order two parts. Please see as follows for detailed repair instructions: Release the track stops from the upper dishrack rails and pull the upper rack from the dishwasher and place it upside down on a work surface. Raise the wheels to the maximum height. Release the top of the long rear clip from the dishrack tine and push the clip down to the release point and remove it. Press the tab down on the front clip move the clip up to pull it off. Release the locking tabs on the clip in the middle of the height adjuster and remove the clip. Using a slot screwdriver pry the housing cover down and out to release the upper tabs on each side. Pry the bottom of the housing cover out of the 2 lower locking tabs. Pull the housing cover off the rack. Remove the adjuster housing and wheel assembly and repeat the procedure on the other side. Slide the vertical portion on the new wheel assembly between the fourth set of vertical tines from the back of the dishrack and rotate the wheel assembly so that it lays flat against the side. Insert a positioner clip above the rear wheel and snap the tab into the slot. Install a positioner clip on the front wheel. Position the adjuster body over the vertical portion of the wheel assembly and push in into the slots. Locking tabs at the bottom of the adjuster body engage the wheel assembly once it is fully inserted the tabs. Insert the actuator lever into the adjuster body with the thumb pad facing the front of the rack. Two half-circle cutouts on the adjuster body hold the actuator in place. Push the adjuster body down and install the adjuster cover. Install the adjuster cover mounting screws. Repeat this process on the other side of the rack. Push the upper dishrack onto its tracks.

Dishwasher Dish Rack Adjuster Kit - Left and Right Side

★★★★★

★★★★★

263 Reviews

Rack Track Stop

★★★★★

★★★★★

25 Reviews

The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes properly, the rack stop may need to be replaced. The replacement part may differ slightly from the broken part, depending on the model. However, the different styles are interchangeable. This product is sold individually and comes in both a white and grey plastic version. Many of our customers found this repair to be very easy and takes less than 30 minutes to complete. Simply snap the old part out and snap the new part into place. You will not require any tools to complete the job. This is an authentic part approved by the manufacturer.

Rack Stop Clip

★★★★★

★★★★★

27 Reviews

This manufacturer-approved Rack Stop Clip is a gray plastic part which can be installed with a screwdriver. Measuring slightly over an inch in length, it prevents the rack from sliding too far and falling off. If broken or damaged, then the rack will slide too far and this is a sign the part should be replaced. It attaches to the end of the top dishwasher rack. This clip can be used for the left or right side, and is sold individually. It is a good idea to replace both sides at once. To make this repair, start by pulling out the rack, then, using your screwdriver, reach in behind the rack stops and press the clips in. You should be able to remove the stops from the track from here. Next, you should be able to slide the track back over the rollers and snap the new track stop into place.

Tine Pivot

★★★★★

★★★★★

16 Reviews

The tine pivot clip, also known as the tine row pivot, is used in dishwashers and is located in the upper dishrack. At around 3 inches in length, the clip is used to keep the tine row in place in the dishrack. If your clip is cracked or damaged, it is best to replace this part. To repair, first lift the release tab and hold the other side to prevent it from falling off. After lifting it off, you can set the new clip on the tine row and lock it up. Refer to the manual provided by the manufacturer for further installation instructions and guidance. Remember to wear work gloves as a safety precaution. This repair was rated as very easy by our customers and should be done in 15 minutes or less.

Dishwasher Dish Rack Slide Track - Left Side

★★★★★

★★★★★

30 Reviews

Dishwasher Dish Rack Slide Track - Right Side

★★★★★

★★★★★

38 Reviews

Dishwasher Positioner

★★★★★

★★★★★

9 Reviews

Also known as rack adjuster. Sold individually. This is an original part from KitchenAid, Kenmore, Whirlpool, Jenn-Air, and Maytag for use with Dishwashers. The dishrack adjuster arm positioner clip holds the adjuster arm in the right position on the dishrack. The most common reason for replacing the strap is if the rack will not stay in its desired position. This part is sold individually. There are no tools needed to replace the positioner.

Drawer Track

★★★★★

★★★★★

8 Reviews

This drawer track or rack slider bar is for use in your dishwasher. It connects to the upper dish rack, and allows the rack top slide in and out. You may need to replace this part if your old rack will not slide out, or your old drawer track is warped and causes the dish rack wheels to fall off or jam. You will need a flat blade screwdriver to remove the rear stop, so you can pull out the drawer track.

Adjuster Housing Cover

★★★★★

★★★★★

1 Review

The adjuster cover goes on the outside of the adjuster housing. It is used to support the height adjuster and also protects the internal components of the adjuster housing.