This manufacturer-approved Rack Stop Clip is a gray plastic part which can be installed with a screwdriver. Measuring slightly over an inch in length, it prevents the rack from sliding too far and falling off. If broken or damaged, then the rack will slide too far and this is a sign the part should be replaced. It attaches to the end of the top dishwasher rack. This clip can be used for the left or right side, and is sold individually. It is a good idea to replace both sides at once. To make this repair, start by pulling out the rack, then, using your screwdriver, reach in behind the rack stops and press the clips in. You should be able to remove the stops from the track from here. Next, you should be able to slide the track back over the rollers and snap the new track stop into place.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your KitchenAid Dishwasher Rack Stop Clip
Troubleshooting
This part fixes the following symptoms:
Door won’t close | Door latch failure | Not cleaning dishes properly
This part works with the following products:
Dishwasher.
This part works with the following products:
KitchenAid, Kenmore, Whirlpool, Jenn-Air.
Part# WPW10195622 replaces these:
AP6016778, W10195622, WPW10195622VP
Customer Reviews
Average Rating:
★★★★★
★★★★★
28 Reviews
4.8
Filter By Rating:
5 Stars
24
4 Stars
3
3 Stars
0
2 Stars
0
1 Star
1
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Dominic P - December 10, 2023
Verified Purchase
Bonne piece
Un peu chère quand même 45 $ avec la livraison pour 2 stopper
★★★★★
★★★★★
Mary B - May 21, 2023
Verified Purchase
Easy repair .
The part was in good condition. I followed video and did a few test tries until I rotated the part into correct position! It then snapped easily into position. All now working perfectly.
★★★★★
★★★★★
BETHANY N - May 17, 2023
Verified Purchase
WORKED
Got the job done, fit properly
★★★★★
★★★★★
Judy M - March 29, 2023
Verified Purchase
Easy repair.
Fast delivery Great condition.
★★★★★
★★★★★
Neil W - June 29, 2021
Verified Purchase
Easy to I stall
Part came fast and installation was easy
★★★★★
★★★★★
Marilyn B - April 2, 2021
Verified Purchase
Easy to use and works perfectly.
The part was shipped on time and easy to install. The appliance is back in great working order.
★★★★★
★★★★★
Dave H - February 21, 2021
Verified Purchase
Easy installation-exact match
Received in 3 days. Easy switch. Works great. Thanks
★★★★★
★★★★★
John H - August 16, 2020
Verified Purchase
worked well
Arrived in good condition and appliance is back working again
★★★★★
★★★★★
Robert W - August 12, 2020
Verified Purchase
Very easy to order, prompt delivery, exactly what I needed.
The part was exactly what I needed and they also included a how to video which was very useful.
★★★★★
★★★★★
Brian C - June 22, 2020
Verified Purchase
Rip off way overpriced
Extremely overpriced for a tiny piece of plastic. Too bad they didn't make the original strong enough to last. The third overpriced piece of cheap plastic I have had to buy for this dishwasher
< Prev
1
2
3
Next >
Customer Repair Stories
Average Repair Rating: 4.4 / 5.0, 23 reviews.
What's this?
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
The rack stop clip on the upper right rail broke. I ordered two replacements and installed the part in about 15 minutes!
I pulled the upper rack out of the dishwasher. I then removed the broken rack clip stop on the right side and reinstalled the new replacement clip. I then put the rack back onto the rollers and voila, the upper rack no longer fell down off of the tracks!! Problem solved and the replacement clip only cost $8.95!!
Other Parts Used:
Patricia from MC CORMICK, SC
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
6 of 6 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
rack stop needed to be replaced
took out the top dishwasher rack. Pulled out the track needing repair. used a flat screwdriver to pry off the defective stop. Slid the track (without the stop) back over the rollers. Snapped in the new track stop and that was it.
Other Parts Used:
Bruce from Milwaukee, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
5 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replace parts to basket
did need the strength of husbands hands to pop out old parts
The rollers on my top rack in my dish washer were broken and wouldn't stay on every time you pull the rack out it would fall. So I ordered the rack adjuster kit and it had everything I needed to fix it. Works like brand new now not hard to change and put new on took about 15 minutes approximately. D
Just remove from dishwasher the top rack and remove the old rack adjusters and put the new ones on , only 2 screws to each side and you are back in business. Very easy to change out. Put the rack back in slots in dishwasher and that's it.
Plastic pieces had broken on both the top and bottom racks
The parts select site had an excellent breakdown of what I needed to replace. When I got the pieces, however, it wasn't so apparent how to do it. I actually used YouTube video to show the process.
The trickiest part was actually uninstalling the broken pieces. I had to work backwards through the YouTube video.
The other tricky bit is having a sense of how hard you can push to snap plastic pieces in and out.
Also, watch the whole video! I didn't, and I ran out for a tool (a star driver, I think that's what it's called) that was actually in the bag of screws that came with the assembly.
It seems like Kitchen Aid realizes they have a problem with plastic fatigue, because they have replaced some of the plastic parts with metal.
If you take your time and stay organized this is a very doable repair.
Wheels on top rack broke off on 2 dishwashers within one week of each other.
The picture of some of the parts for the repair did not match some of the parts received. So new pictures of the most recent parts need to be included in the repair kit. The repair kit only has a few parts, which makes it relatively quick to center and connect. The written instructions were not perfect, especially in identifying which direction the rack adjuster clips need to be oriented, but it was pretty easy to figure out since the clips are well aligned when only put in one way. My son and I connected the right and left rack adjuster wheel assemblies to the upper dish baskets for both dishwashers in about 15 minutes each. That time included taking off the old rack adjuster wheels assemblies and installing and make sure the two new assemblies worked well and fit in the upper water supper valves correctly.
Upper drawer rack stop clip broke caused one side fell off rail.
I followed the YouTube attached with PartSelect email invoice to fix it. I am very happy PartSelect sent repairing video instruction and took me less than 15 minutes to get it done. Awesome!
Other Parts Used:
Pooi from TORRANCE, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Upper rack wheels broke
Originally I ordered the rack stop clips but realized I needed the whole upper rack repair kit. It entailed pulling off parts and popping new parts on. Very easy and simple.
Other Parts Used:
kerry from PRNC FREDERCK, MD
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
3
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
12 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
James
July 20, 2017
How do I take this part off to replace it
Hi Oscar, start by pulling out the rack. Then, using a small flat blade screwdriver, reach in behind the rack stops and press the clips in. From there the stops can be pulled off the track. I hope this helps!
16 people found this helpful.
Was this helpful?
Thank you for voting!
Paul
July 20, 2017
The upper dishrack in my dishwasher keeps falling off of the rails. This is a gently used dishwasher and I wanted to confirm that this is the rail stop part I would need to prevent the top rack from coming off
Hi Paul, yes, this is the right part. The purpose of the rack stops clips are to clip in at the end of the top dishwasher rack to prevent it from sliding out and falling off. Please let us know if you have any further questions.
9 people found this helpful.
Was this helpful?
Thank you for voting!
Mike
July 20, 2017
Looking for the dishrack stop for my upper dishrack on my dishwasher. I think my unit has two of these- one on the left and one on the right. Does this purchase only come with one stop and is it for the left or the right or both?
Hello Mike, this order will come with 1 dishrack stop, and can be used for the left or the right side. If both dishrack stops need replacing, you will have to purchase 2 of these. Best of luck with this repair.
5 people found this helpful.
Was this helpful?
Thank you for voting!
Tim
February 19, 2018
Re: Wpw10195622 “rack stop clip”. Your answer to multiple questions (paul, et al) is wrong. This part goes in the back end of the “slide rail”/“drawer track” (wpw10195623) to keep the track from coming off, and to remove or replace when removing and replacing the rail. It is more robust than the front rack stop, which is part of the “drawer track” assembly and apparently not available separately. This front stop consists of a robust plastic base, that is molded (melted) permanently onto the front end of the metal rail (“track”), and a flimsier plastic from stop that snaps on and swivels 90 degrees to allow you to remove the drawer for cleaning. This front swiveling drawer stop is the one that breaks so that the rack comes off the rail if you pull it out too far. The only way to get this part is to replace the “drawer track” (above), or canabolize another machine, since it is part of that assembly.
For model number 66513252K114
Hi Tim,
Thank you for your information, that is very helpful. One thing to note is that not all models are actually formatted the same. Though many models use the same sort of parts, they are not all used the same way. Some models use this clip as the front piece, in your particular case it is used as the back piece and the front piece only comes with the rack track. If you ever have any questions about parts just let us know, we can generally determine what part goes where by using your diagrams. I hope that helps. Have a great day.
5 people found this helpful.
Was this helpful?
Thank you for voting!
Penny
October 22, 2019
Is the stop clip the same on the front of the rack and the back of the rack?
For model number KUDC10FXWH5
Hi Penny, thank you for your question. They would be different parts. The front clip is offered separately but the back clip is only offered with the track. I hope that helps. Good luck with your repair.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Penny
October 23, 2019
This is a follow up question from yesterday about the stop clip on the upper rack of my dishwasher. The picture of the rack shows the stop clip being at the back of the rack, but the answer i received yesterday stated that the stop clip is sold separately for the front and the back clip is sold connected to the track--which is correct?
For model number KUDC10FXWH5
Hello Penny and thanks for writing.
PS11750071 This rack stop clip works for either the right or left side of your upper dish rack. This part is sold individually.
This part fixes the following symptoms: Door won’t close, Door latch failure. We hope this helps. Please contact us anytime.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Steve
November 11, 2017
I need to replace the upper rail clip so the wheel does not come out when the basket is pulled forward. The instructions say a screwdriver is needed to remove the old and screw in the new clip. As i look at it, it does not screw and has more of a rivet attachment. Do i need to replace the whole rail ? Is there instructions ?
For model number KUDC10IXSS7
Hi Steve,
Thank you for your question. We had a similar question asked by another customer, here is the answer: start by pulling out the rack. Then, using a small flat blade screwdriver, reach in behind the rack stops and press the clips in. From there the stops can be pulled off the track. I hope that helps. Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Nicky
February 28, 2020
The front clip on the top rail has broken and i'm wondering if this can be purchased separately for this model or if i need to get the entire rail. Note that this clip on this model is different than the back clip. It snaps open so that you can remove the top drawer completely.
For model number 13922k012
Hello Nicky, thank you for your question. The front clip on the upper rail is only available by ordering the whole rail. You will have to order PartSelect Number PS11750072. Good luck with your repair!
Water isn't entering the washer it starts but the water doesn't fill
Hello Marcelle, thank you for contacting us, In order for us to locate the correct parts and repair information we will require the model number of the unit. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. We are looking forward to hearing from you.
Was this helpful?
Thank you for voting!
Robert
July 30, 2021
Left stop on top rack broke need to order both probably ,but it work then rack drop down on one side wouldn't align with water hole . Don't know if realign or what.
For model number wdt710paym3
Hello Robert, Thank you for your inquiry. You may also need to replace the rollers that hold the rack to the track as well, part# PS11753471. Hope this helps.
This drawer track or rack slider bar is for use in your dishwasher. It connects to the upper dish rack, and allows the rack top slide in and out. You may need to replace this part if your old rack will not slide out, or ...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11750071
Manufacturer Part Number: WPW10195622
