Models > KGCD807XBL00 > Instructions

KGCD807XBL00 KitchenAid Cooktop - Instructions

All Instructions for the KGCD807XBL00
46 - 60 of 122
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Plastic Burner Knobs cracked
Pulled off the old and pushed on the new. Took less than a minute.
Parts Used:
Burner Knob - Stainless Color
  • Sid from Saint Francisville, LA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
erratic spark from electode,gas would no ignate.
Removed the two fastening screws with a small square head screwdriver,lifted the burner head disconnected wire from damaged electrode. To install just reversed the steps,total time less than ten minutes.
Parts Used:
X-Large Burner Head with Electrode
  • jose from san juan bautista, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner would not light
Replaced burner assembly.
Parts Used:
X-Large Burner Head with Electrode Torx Screw
  • Mike from Big Canoe, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Knobs on the new JennAir Range I just purchased started to melt and when they were called they did nothing about it. I had to call and get new knobs at my cost.
Very easy, just removed the old ones and the new ones just clicked on.
Parts Used:
Burner Knob - Stainless Color
  • Sherry from Mentor, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Electronic ignitor malfunctioned
First reviewed other review on this repair. Disconnected ignitor system from electrical source (pulled plug); removed 2 screws holding casing in place; removed it from the cooktop; & removed additional screw holding ignitor. Replaced ignitor and reversed the process. Done.
Parts Used:
Burner Electrode
  • Richard from Sherman Oaks, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Being dumb enough to buy Jenn-Air appliances
I removed the old knob and replaced with a new one from the plastic package. Biggest challenge: opening the new plastic package. It if very nice to know you have many of the parts I will need over the next 20 years.
Parts Used:
Burner Knob - Stainless Color
  • Brian from Rancho Mirage, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken stove knobs
remove old knob, plce new knob on.
Parts Used:
Knob - Chrome
  • Jacob V from Houston, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
cracked knob
put new knob on
Parts Used:
Knob - Chrome
  • Charlie from Willis, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ignitor sparking at bottom, not the top
Removed two star screws from the top of the burner, disconnected the wire going to the Ignitor, removed the old ignitor held in with one phillips screw, installed new ignitor and re-installed the burner assembly. Simple!
Parts Used:
Burner Electrode
  • Edgar from COCKEYSVILLE, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner nob broken
Popped the old one off and installed the new one.
Parts Used:
Burner Knob - Stainless Color
  • John from Mesa, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken knobs
First I removed the old damaged knobs by pulling upward on the knobs. Then I replaced the damaged knobs with the new knobs being careful to align the male and female connection. After installation I tested each burner for proper operation. As a final test, I asked my wife for her opinion. We're happy!

Charles & Dorothy
Parts Used:
Burner Knob - Stainless Color
  • Charles from Grenada, MS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Knobs for the cooktop burners did not fit so I have returned them and still do not have use of all burners due to lack of knobs
Could not put a square peg into a round hole....parts did not fit and I do not know how to find the model number but the knob has two flat sides.l....the knobs you sent did not.
Parts Used:
Burner Knob - Stainless Color
  • Pat from MCKINNEY, TX
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The knob does not go down; it sticks up too high. Question? Maybe knob is not for position 2. Does it matter which place you put it on?
I tried to put knob on number 2 location. Looks like I need number 1 knob.
Parts Used:
Burner Knob - Stainless Color
  • Joanne from BRANCHBURG, NJ
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Auto igniter had gone bad.
Take out 2 T15 torx screws. Lift burner assembly, disconnect igniter. Make sure wire does not return into hole. I put A paperclip on it. Connect new burner assembly. Clean under old burner. Install burner assembly with screws. Test burner.
Voila!
Parts Used:
X-Large Burner Head with Electrode
  • Aubrey from EADS, TN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Igniter clicked but burner would not light
Once I got over my first time jitters this was easy. Lucky for me the old screws went back in just fine. The recommended 8/18 x 3/8 screws were way to small to be usable. Check the length of your existing screws if you can before purchasing the recommended ones.
Parts Used:
Screw, 8/18 x 3/8 Large Burner Head
  • Margaret from ROCHESTER, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the KGCD807XBL00
46 - 60 of 122
Back to Top