GTWN4250D0WS General Electric Washer - Instructions

I followed previous parts select customers advice exactly, of replacing the dampening straps, and it worked perfectly. Thanks-A-Million!

As the video described. The two rear dampening straps holding screws were only accessible from underneath making their installation much more difficult than the front ones which were accessible from the top.

replaces as per video. Very helpful

Remove two bracket screws. Removed hose. Put new hose in place using same bracket and screws. inserted end of hose into washer drain. Secured hose to cold water hose with two zip ties.

removed three screws from back panel used putty knife to remove front panel and dampening strap were there to remove.

After receiving the wrong part 2x instead of magnet assy I received a metal clip ring. ordererd magnet assy from another source. iNSTALLATION IS VERY SIMPLE. REMOVE 2 SCEWS IN THE LID WHICH HOLD THE MAGNET IN PLACE AND REPLACE THE MAGNET WITH NEW ONE. TEST TO MAKE SURE ALL OPERATIONS ARE NORMAL.

Unplugged machine. Used tape markers to identify knobs then removed control knobs with vigorous straight pull. Unscrewed three screws on rear of control panel face and tilted control panel over with a small sideways slide, to expose circuit board. Laid new circuit board alongside old and transferred jumper block and wiring terminals from old board to same positions on new. Unscrewed old board and removed. Put in new board and tightened screws. Replaced back panel and knobs. Plugged in machine and tested. Done!

really easy repair, just open the front cover panel & removed the Drain Pump.

Followed the video with one exception. The hose clamps were the spring-loaded type and putting the back hose clamp on was a problem, so I substituted a nut driven hose clamp. Other than that, no problems.

Popped cap off of agitator and used 12inch extension with 3/8 socket to remove bolt. Pulled off agitator and turned upside down. I then used 4 flathead screwdrivers to depress tabs on old coupling and flipped agitator back over and used a long screwdriver to push old coupling out. Flawless! Wiped everything down and pushed new agitator coupling right in place! Perfect! Put everything back together and washer is back in business!! Thank you PARTSELECT!!

The job was rather simple. After removing front panel with the aid of a putty knife to push back the spring clamps under the top panel, the pump is in plain view. Remove the two mounting screws and push back the spring clamps that secure the connection hoses. Squeezing the spring clamps that hold the hoses onto the pump can be a bit troublesome so I removed the spring clamps completely and replaced them with radiator hose clamps which made the job a whole lot easier. Replaced the front panel and the job was finished.

Removed the screws from the control panel and flipped it open. Used putty knife to pop the retaining clips that held the front panel of the washer in place to expose the drum itself. Noticed black gunk build up in hose connecting the drum to the water level pressure switch.

Disconnected the hose at both ends. Attached the new hose to the pressure switch and proved it was working by blowing into the hose and getting the water to stop flowing into the washer.

Taped the old hose to the new hose so I could use it as a pull-wire to guide the new hose through its protected housing. Attached the other end of the new hose to the tub and voila, all was well.

The video I watched said to remove front panel, control panel, and top panel. After I removed the front panel, I was able to remove the lid switch and splice the wires together and reinsert in the mounting without removing the other panels. Secured with wire tie and put front panel back in place. This did not, however fix the problem.

pulled up on agitator and it came off and replaced it with the new one

First tried pulling the old agitator out by hand but couldn't get my fingers under it to pull upward. Tried several times but no success. Finally put two metal rods about 8 inches long in the holes in the bottom of the agitator and used them to lift upward, it came up immediately. I then pushed the new agitator down into the slot and it was finished. There is always a way when you think about it.you are a winner.