GTWN4250D0WS General Electric Washer - Instructions

Easy as can be. Similar but not exactly like the YouTube videos, but close enough. Biggest problem was pulling the filler tube off of the mixer and re installing the tube. Nothing to get worked up about.

Removed the front of the washer using a putty knife. Removed the old belt and used a shop-vac to c,San up the insides. Placed the belt on the pulley and used three med sized zip ties about one inch apart. I cut off the exposed tail of the zip ties. Got the belt started around and put the belt onto the small pulley. Keeping an eye on the small pulley to make sure the belt did not slip off, I had to push it up a time or two. Then as I pulled the big pulley around, one zip tie broke, replaced it and continued pulling the big pulley, it got tough but with one knee pushing on the drum and pulling with one had it went on. I did slowly turn it to align the belt on the big and small pulleys. Not hard, I recommend a bright flashlight and gloves. I saved a good buck doing it myself :-)

replace lid switch

Removed the two hex head screws from the broken strap and replaced it with the new one. The other three straps were not broken but I also replaced them, again, one at a time. This made sense,since the machine was at least ten years old.

Removed the front cover with a screwdriver, by locating and slightly prying the metal clpis back to release the cover. Then I removed one screw (only one visible) from the strap that hold the top cover/lid down. With a little prying, I lifted the lid up out of the way, and suspended it with a cord. I removed the old dampener straps and replaced each one at a time with the new strap. It was not to hard to get to the screws (I have large arms), and it only took me nearly a half hour to complete the task. It would have been easier if I used two different size nutdrivers, but it was easy enough with an adjustable wrench. Then simply put everything back to together in reverse order of how I took it apart. The wife was impress that I fixed another thing around the house.

Removed the front panel. Removed the washer top. Removed and replaced each strap. Very simple repair.

Reach down and grab the base of the agitator with both hands and yank up with slightly more pressure on the left or right, whichever side you prefer. This will break loose the holding clamps/pull straight up. To re-install: align slots and push down until it snaps. Simple as that.

Watched the video. Followed the instructions. This has to be one of the best sites I have ever encountered. Even a caveman could fix the problem after watching the video.

I pushed a small screwdriver under the top lid and pulled the front out and lifted it out or the way. The rubber hose had two clamps holding it. One you loosen with a flat screwdriver and the other one you squeeze with pliers to remove hose.Then replace hose and put front back on. It's very simple.

Surprisingly easy. I took the screws off, then pulled off the drain hose. I then inserted the new hose, and put back the screws. Amazing quick!

Unplugged...Removed back from washer...Using nut driver-cordless drill...Inspected hose-found leak....Removed hose with pliers & screw driver.....Than dried the hose...& than for temporary fix (for the wife to continue washing) used some Epoxy for rubber.....Than ordered new part. Received and reinstalled replacement. Thank you

Repair went well but there was clips to the door switch not in the video. Still was easy to work around and complete.

replaced broken straps all 4. washer not working ]. replaced lid switch with wire harness.replaced bad old belt.working fine now. my wife is very happy. thanks for your videos and how to do the job right.

Repair video is spot on but does not emphasize securing the drain pump to the washer before reattaching hoses. This holds the pump in place allowing you to compress the hose clamp while pushing on the hoses.

The hardest part is lifting the washer to get a the bottom. Disconnect the power, shut off water. Disconnect hoses and drain hose. Move washer from the wall about 2 feet. Tilt up front of washer. I used 4 12" long 8x8 inch lumber, lift washer….place one on each from corner. Lift again, place 1 more 4x4 on each existing 4x4. Now remove the belt off the 3 pulleys. Use the flat blade screw driver to remove the C clip holding the Pully on the shaft, with the flat bladed screw driver and hammer. Once the C clip is off remove the metal washer, pulley, plastic lock (apart of the bottom of the pulley & the thrush bearing and it's washer. Using the parts supplied (the "new thrush bearing is a bearing and washer combined) replace as you removed it. Thrust bearing, pulley, washer and, c clip. I tapped mine on using the flat bladed screw drive……becareful not to break it (they did supply 2 for me in the repair packet) make sure he c clip is secured. Lower the washer after removing all the tools from under the washer, by reversing the lift sequence. Slide the washer in place. Connect the hoses back up. Plug it in.Reconnect the drain hose, you should be good to go.