All Installation Instructions for Roper Range FES330KQ0

element burned out shortly after purchase of range, one was purchased locally and did not fit properly, causing element to burn out

replaced element with new one , worked perfectly-

Parts Used:

Surface Burner Element - 8 Inch

Sue from INDIANOLA, MS
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

cooktop on the rt side would just keep getting hot

Removed the ifinite controlswitch and replaced it but i dont believe it is wired correctly. now it wont get hot until it is set on four or so. think i the way it is wired.

Parts Used:

Infinite Control Switch, 6"

Cooktop Cleaner

Michael from GRAND PRAIRIE, TX
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven would not heat up.

Unplugged the range. Opened the oven door and took out the shelves. Took the right screw out, but had trouble getting the left one out do to the age of the range. Unhooked the two wires and took the element out. Put the new one in and hooked up the two wires. Attached the two screws and checked to see that the element laid flat and then tighten screws. Closed the door and plugged the range back in and turned the oven on and it worked perfect.

Parts Used:

Oven Bake Element

Johnie from PARKERSBURG, WV
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

I snapped a bolt on the main power terminal block when connecting the pigtail.

Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

Parts Used:

Range Main Power Terminal Block

Frank from Palm Coast, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

3 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Oven temperature was 50 degrees off

Unplugged stove.
Pulled stove out.
Unscrewed screws and removed cover.
Removed & replaced sensor.
Reinstalled cover & screws.
Plugged in stove and pushed back in.
Only problem was when I pulled stove out, lid opened and disconnected the gas line to a burner.

Parts Used:

Oven Sensor

Gregory from BRIDGEBORO, GA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

wire came loose and shorted out

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

Parts Used:

Range Main Power Terminal Block

Elizabeth from HOUSTON, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

The side trim on the glass door needed to be replaced.

After we put the latch pins in, the door was easily lifted off. We placed the door on the table and unscrewed the trim pieces. The new trim pieces went into place after we cleaned the door. We slipped the door back on the oven and removed the hinge pins.

Parts Used:

Hinge Pin Kit

Mary from LARAMIE, WY
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

cleaner

just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you

Parts Used:

Cooktop Cleaner

Mary from Duarte, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Replacement of one small and one large electric element burner and drip bowl.

Replaced old parts with new. Elements and drip pans fit perfect and snug. No issues. Would purchase again if needed. Thanks!

Parts Used:

Surface Element 1250W - 6 Inch

Surface Burner Element - 8 Inch

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

Samuel from RICHMOND, MI
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

My drip bowls were scorched and discolored and difficult to clean

I removed each surface coil burner from its receptacle; removed the old drip bowls and replaced with the new ones; my stove looks good as new.

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

Claudia from Milwaukee, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

burnt out drip pans

I had been putting off this repair for months! I finally sat down to explore ordering the parts. It was so easy - I wish I did it a long time ago. When the parts arrived, they were exactly what I needed.

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

Barbara from KAMUELA, AL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Bad Receptacle

I had a receptacle melt in front of my eyes. I few questions later PartSelect.com showed me the part I needed and was checking out in less than 10minutes. Part arrived 3 days later and 20 minutes after that it was installed. I'm Amazing!!! No, PartSelect.com is AMAZING!

Parts Used: