All Installation Instructions for Roper Range FES330KQ0

Replace burner drip pan

Removed electric coil replaced pan and reinstalled coil. Part fit just right and no problem.

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

Ray from Council Bluffrs, IA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Lost element clips and bad burner element

Pushed elements to remove them. Put on new clips by snapping on clips to all burner elements. Tilted each burner 60 degrees allowing room for the clip to clear the range hood and pushed the contacts on the burner elements into the electrical slot. Turned on each burner to make sure they work. All burner element's work fine.

Parts Used:

Surface Burner Element - 8 Inch

Range Element Clip

James from CAMBY, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Oven not heating properly

Unplug the oven, pull it out and empty the inside of the oven. The bottom heating element just unscrews from the back of the oven with two screws. Pull it out from the back of the oven and gently pull off the electrical connections. Reattach them to the new heating element, put it back into the oven and reattach the screws. Turn the oven on and check to make sure that the new heating element is working. Put everything back in the oven and you're done!

Parts Used:

Oven Bake Element

Matthew from Greenville, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

the drip bowls had rusted through

a really simple fix! the parts came really quickly and all i had to do was pull the heating elements out along with the old drip pans and line up the new pans and push back in. the drip pans weren't 100% perfect as they were a universal fit, and were missing the clips that help the heating elements i nplace, but they look fine and do the job all the same.

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

DANIEL from sanborn, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

door glide broken

removed the old ones.then installed the new ones.

Parts Used:

Range Rear Drawer Glide

David from Port Orange, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

range handle fell off and screw got lost

It was worth the money for that little screw, since I didn't have to run all over trying to find the right one.

Parts Used:

Range Screw

Frances from palm beach gardens, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Block broke

Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

Parts Used:

Range Main Power Terminal Block

Edward from Crimora, VA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

1 of 4 people found this instruction helpful.

Was this instruction helpful to you?

replacement of drip bowll

take the old one out, but the new one in.

Parts Used:

Drip Bowl - 8 Inch

Gudrun from Santa Fe, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Ugly looking drip bowl.

Repair? What repair? I just removed the old drip bowl and replaced it with the new one. Piece of cake.

Parts Used:

Drip Bowl - 6 Inch

Irina from Green Cove Springs, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Oven gets too hot,if set at 350 it heats to 550. Changed the sensor and was not the problem.

Took off the screws on the back of the stove and took out the sensor, and put in the new one.

Parts Used:

Oven Sensor

Joanne from Negaunee, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Both outside door handles turned very beige

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Parts Used:

Spray Paint - 12 oz. - White

Howard from Boynton Beach, FL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

23 of 76 people found this instruction helpful.

Was this instruction helpful to you?

Drawer glide was missing and the trim on the door was broken

Ordered the replacement part., removed the old trim from the door and reinstalled the new trim. On the drawer glide, I simply reattached a new one to replace the one missing.

Parts Used:

Door Trim Kit - Black

Range Front Drawer Glide

Carol from Lakewood, CO
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

12 of 45 people found this instruction helpful.

Was this instruction helpful to you?

Element terminal connection loose caused overheating and carbon buildup.

Sanded element contact, replaced connector block. The easiest part of the task was ordering the part online. You made it unbelievably easy. I was amazed!

Parts Used:

Range Receptacle Kit

Mark from Louisville, KY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Could not get self cleaning oven to engage

Removed back of stove, 8 screws, removed original latch assembly and installed new assembly. One thing that can cause you difficulty is that the rod that connects the assembly to the front latch on the door can disconnect and has to be reconnected.[Problem]

Parts Used: