All Installation Instructions for Roper Range FES330KQ0

The part doesn't seem to fit the glass door

I still don't have it back together! The first time we ordered the part the gentleman sent me the trim for the left side which seemed to be fine but while replacing it the old part (right side) broke. Ok. so I called to order same part but for the right side. Well, the lady told me I could only order the oven door trim kit, which seems to be too large. I don't think she understood me. Why the 1st time ordering I could get the left side only now when ordering the right side she says we don't sell it that way. Very confused and still can't use my oven since Dec,19th!!

Parts Used:

Oven Door Trim Kit

George E from SEVIERVILLE, TN
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

oven handle broke

new handle arrived black for white oven - screws did NOT fit new handle- glass came off the door when removing old handle

Parts Used:

Range Door Handle

Jim from CAMDENTON, MO
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Dual burner would go to highn heat.

Watched video & did just guy in video did. Very easy job & the burner works like new.

Parts Used:

Infinite Control Switch, 6"

LOUIS C from GRAND JCT, CO
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Broken Door Handle

Remove the side covers. Remove the 2 screws on the back side of the door, hold on to the glass and front panel, they will fall out. remove the 2 screws holding the handle. Put the new handle in place and insert screws, note the old handle had metal inserts that are threaded, the new does not. Had to push very hard and let the screws bite into the plastic.

Parts Used:

Range Door Handle

Daniel from BROOKLYN, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Broiler element burned out

After doing a YouTube search. I successfully completed the repair by easily diagnosing the issue with the element.
I watched a video about 5 most common problems with whirlpool broiler elements.
The first being to inspect the element for damage. I found a small section that appeared to be rough and had a raised bump.
I decided to order a new element because the oven is older and it wouldn’t hurt to install a new one even if this wasn’t the issue.
Once the part arrived, which it did quickly, I followed the video instructions. It was easy and straight forward. I completed the task in under thirty minutes. It was very simple and I now have a functional broiler element.

Parts Used:

Broil Element

chris from HILTON HEAD, SC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

I was trying to remove the oven door so I could clean the glass. Spills had run down between the layers of glass.

This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.

Parts Used:

Hinge Pin Kit

Karen from Oklahoma City, OK
Difficulty Level:
Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

the fastener became loose and dropped into the stove

This is a cook stove that is used 5 months a year. We have not fixed it yet because we are now in Florida the stove is in New York. We ordered that part just before we left NY for FL so the repair will be done in June of 2021.
George Clark

Parts Used: