BX521VCPWR (P1325030W W) Amana Refrigerator - Instructions

My repair job was probably the easiest one of all, as the new shelf was simply snapped into place and the job was done. I saved a lot of money from buying the part locally too.

carefully

I simply used my cordless drill with the right sized socket attachment to remove the screws. I left the door on which wasn't as difficult as I thought after reading other stories. I even had to contend with my three year old who wanted to know what was going on and if she could help. As my wife is deployed it falls to me to become both parents, watch after her and take care of chores. With all that said it still only took me about half an hour to replace the old gasket with the new one. As far as the gasket goes I wish the magnet was more powerful because there is still a gap unless you push and hold it closed for an extra second when closing the freezer. A pain but at least it is not torn. Before buying I recommend searching for a parts/service center that that talks about the whole part not just how to replace.

Installed missing spacer

I did not do the repair yet, there is no schematic on how to route the hose; also no description of how to do the routing/connections.

I loosened(but did not remove) the 1/4" sheetmetal screws around the perimeter of the door liner. (they are numerous and they are hidden in the fold of the gasket) I removed the old gasket. With the screws still loose, I installed the new gasket. After insallation I re-tightened the liner screws. Several gaps were noted and eliminated by gently heating the gasket with a hair dryer. (be patient , it takes some time)

First we read all the comments by other handymen. This was really helpful. Then we took the door off and removed the old gasket with a nut driver. We tried to slip the new gasket under the edge with a thin spatula and didn't have much luck. Then we remembered someone saying that is was a good time to take the door apart and check to see if there was ice build up in the door. It was so bad we took out the frozen insulation and replaced it with new....$4.00 at the hardware store. While the door was apart we put the gasket on and put it in place and tightened it to the door. This worked very well for us. This saved us from having to buy a new refrigerator/ freezer. Thanks.

There were no instructions with the new gasket which made the job difficult. After great difficulty I called an appliance store and learned that the gasket should be soaked for several minutes in very hot water to make it pliable and easier to install. Also, the plastic insert that the gasket fits into should only be loosened and not removed when inserting the gasket. Lastly, the door should be removed and placed on a table to allow leverage to be applied. Installing it while still on the door is almost impossible.

I found the instructions on line which seemed very simple but I soon learned otherwise. The instructions say to remove the water line and then firmly pull the fill tube out as it is a tight fit. I couldn't get the tube out and ended up removing the lower freezer door/tray, the upper tray and the icemaker where I found the water had frozen solid in the end of the tube. I used a hair dryer to melt the ice then I could easily remove the tube. After several attempts to install the new tube I finally inserted a 3/8" OD flex tube thru the passage then I was able to slide the new fill tube over this and get it in place. I then reinstalled the icemaker, upper tray and the door/tray assembly. Turned the water on the check for leaks then plugged the unit back in and all is working well.

Removed the slide out bin and then removed the many screws that held the inner panel to the outer insulated door panel. Removed the gasket. Melted the ice and dried the fiberglass perimeter insulation in the door panel. Placed the gasket in position on the door that was lying on the table. Replaced the inner panel screws. Put everything back together.

THERE IS A PROBLEM NOW. THE GASKET DOES NOT MAKE CONTACT ALONG THE TOP EDGE AND AIR LEAKS INTO FREEZER. SIDES AND BOTTOM ARE OK. DO NOT KNOW WHAT TO DO NEXT.

Watch video. Very helpful, followed instructions went in fairly easy. Gasket deformed, used hair dryer could not get to set straight. WAIST of TIME and MONEY. I wouldn’t recommended buying one of these twisted gaskets, buy a new fridge which is what I’m doing tomorrow.

I sealed the freezer with cardboard and duck tape and kept the door attached (I recycled all the cardboard after I was done). I didn't need to use the hair dryer to remove kinks from the gasket because I couldn't get to the repair for a week and the gasket was in good shape after I took it out of the box.

I almost installed the gasket without removing the plastic door liner (more the twenty small hex screws) but I'm glad I decided to remove it after all. When I removed the plastic liner half of the fiberglass insulation was consumed by a huge block of ice. All these years my freezer had been working harder and wasting more energy than necessary.

I removed all the insulation and replaced it with spray insulation which took longer to allow for the spray foam to cure. The reason I knew what I was doing was because all of you took the time to post your installation experiences. Thank you....

By the way, if you decide to remove the plastic liner for my model, it really helps if someone holds the liner while you attach the first few hex screws. Thank you wife. Also, I'm so glad I had a can of spray insulation in the garage so my wife wouldn't say "how many trips to Home Depot is going to take to finish the job"

The plastic fill cup part is also used to hold one end of the wire “one/off” switch that is manually activated or activated when the ice tray is full. This wire piece fell out because one end, that is part of the plastic fill cup, broke off. The wire switch was fine.

The video demos show you exactly what to do. The repair man showed me a trick to speed up the testing process. The trick is to insert a wire jumper cable to actuate the ice maker and make it rotate. But this isn’t necessary.

Hardest part of this fix is emptying the freezer (bottom with a slide out door) and removing the door.

Why this part is so expensive is beyond me. But I’m happy it was available for a 24yo fridge that still works!!

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

Work was done by service tech. I ordered the arm for my mom to save time when tech came back to do the job correctly.