66513173K706 Kenmore Dishwasher - Instructions

My husband managed, with some difficulty, to finally replace the broken spring and associated door balance kit. He first ordered the spring from this site. Then, after he had laboriously rolled the dishwasher out about 12" - using flat pieces of wood as support, while he lowered the dishwasher onto his homemade rollers - he realized that the corded door balance kit was also broken. So he rolled the DW back in and ordered the part. This site sent an improved door balance kit, and then he went through the same process again. He had to fish the spring back all the way to the very back of the DW and hook it through a hole, using a rod and masking tape (bad DW design, he says). Then after he rolled it back, he noticed a leak in the incoming hot water connector, at the copper pipe compression fitting. Fortunately, a local plumber, with the right tool and expertise was able to quickly fix that problem. (The plumber explained that compression fittings commonly begin leaking if even slightly moved.) Bottom line: A+ for this site, C for KitchenAid design. He says he'd undertake it again, in spite of the hassle.

Video was great help. Replacing the balance parts was easy. My wife and I are in our 80's. Mobility is difficult when it comes to working on the floor. Between the two of us we spent the majority of our time just getting up and down,

Remove power. Remove drain line from sink. Remove hot water line at connection. Remove 2 screws that hold dishwasher to countertop (on top). Pull dishwasher out. Find spring as it has shot to the back when the nylon cord link broke. Hook Spring back in. Attach cord loop end (hard plastic) to spring. Attach other end to door hook. Now stretch spring to loosen cord and slip around pully system. Push dishwasher back in and rehook all connections.

I've had to do this repair at least twice before over the last few years so I stand by my original assertion that the door "balance link kit" reflects very poor design. Well, maybe the design would be okay if the materials were not prone to breakage. However, a simpler spring-only mechanism would have been more reliable. The current design uses string embedded in plastic that latches to a hook area for both sides of the door (frame). The string is threaded around a hub and then to a spring that is in turn connected to the chassis at a rather distant point which also adds to the difficulty due to requiring greater access to the dishwasher sides. It would be much better if the repair could be done without necessitating removal of the entire unit from the cabinet cavity first. I noted that this time around there's been a redesign so that the hub is no longer a round fixed knob but now includes a rotatable wheel. So perhaps there'll now be less wear on the strings that with the prior design! -- D.A.D

Once the cord broke, the stainless steel door became very heavy (eventhough the other side cord/spring combo was intact). My order came within days. The repair kit came with two complete sets (left and right sides). The repair was simple. I used the unbroken side as a guide to fix the broken side. I used all parts from the kit. The part of the repair that required time was to disconnect the electric, plumbing and drain lines. In order to pull the diswasher from the cabinet. Just remember to turn the water back on when you are finished!

1. Removed lower dish tray. 2. Removed old gasket by pulling it out. Came out easy. 3. Cleaned gasket track of food particles with toothbrush and rag. 4. Found center of new gasket and installed new gasket by starting at the top center and work around track pushing gasket in until seated. 5. Tested and no leaks.

watch how it was done on computer

First I removed the two screws holding the dishwasher in place. Then I pulled the dishwasher forward from under the counter about 2 feet, attached the new part to the spring and pulley, then pushed the dishwasher back into place and installed screws.
PartSelect was awesome! UPS delivered to the wrong address and Partselect took care of it IMMEDIATELY! I have ordered more parts from them and no problems. I would DEFINATELY recomend them!

Remove two screws on retainer clips holding dishwasher to counter and pulled out dishwasher. Slide new nylon cord mounting clip into slot where old part is located, rethread the cord around pulleys and attach end to spring. Need pliers to pull and stretch spring. This was the hardest part of the job but not very difficult. Push dishwasher back into counter and replace the two screws into the hold down clips under counter top. Whole job took 20 minutes.

I removed the 2 screws that held the dishwasher under the counter. Pulled the dishwasher out and easily replaced the replacement link. I slid the dishwasher back under the counter and replaced the 2 screws. Everything now works as it should

1. Remove old seal
2. Install new seal

One side of the door balancer broke. I pulled out the dishwasher and made a really strong one out of wire rope and clamps. 2 weeks later it broke again, so I ordered the link kit. I received it in a couple of days. But when I pulled out the dishwasher to replace my broken part I discovered that the original part on the other side broke. I put one of the new parts on the broken side and left my part on the other. I want to see which one lasts the longest.

Disconect electric, remove screws, re-suspend Nylon and plastic suspenders.

The part came pronto. The actual repair was fairly easy, but pulling the dishwasher out it is another story. I replaced the water supply copper pipe by a flexible braided hose. It looks like this is a common problem for these dishwashers.

The part sent was differen in appearance than the original. After calling I was told it would work, and it did. It took 2 people to move the dishwasher out from counter since the levelor,s were a little rusty and it had to be lifted to spray the wd 40 on the screws before we could raise them to pull dishwasher out. We used directions and easily replaced the string pull. After checking the unbroken one we noticed it to was begining to wear out, so we replaced it as well. Good thing their was a pair of replacements. The repair was perfect and I was very pleased with the support.