66513173K706 Kenmore Dishwasher - Instructions

Pulled dishwasher and removed existing springs and attached rope. Ordered the part needed and replaced it somewhat easily. There is a lot of tension because of the spring on the door. Once part was installed we were ready to use our dishwasher right away. Even though the rope was broke on only one side - we replaced both sides.

Pulled the dishwasher out and removed the plastic pulley on the bottom of the unit. Installed the new pulley. wrapped the string assy. around the pulley and attached it to the spring and reinstalled it to the back of the dishwasher. We discovered the front bracket on the dishwasher door was bent slightly causing the string to rub and probably is what caused the string to break. We bent the bracket back into shape and reinstalled the dishwasher in its cavity.

Using Phillips screw driver, removed 2 screws at top of unit, slid it out from under counter. Removed and replaced both sides. The hardest part was to keep the blanket on the unit which I solved with duct tape. Slid the unit back in place and works fine. The repair man wanted $29 to come out and $150. To repair

I watched my son as he pulled dishwasher out part way. The space was a little tight, but he did a fine job of replacing with a new string.

Step 1. Cut off water supply. Step 2. Remove two screws from bottom plate to remove the plate. Step 3. Check that drain line and power supply have enough slack to move the unit out from under the cabinet. Step 4. Remove two screws from top frame that secure the unit to the cabinet framing (note my counter-top is granite so framing goes across the top of the unit; so units are secured directly to the countertop). Step 5. Disconnect water supply line and place something, i.e., a plate, old towel, etc. to catch excess water in the supply line. Step 6. Lower leveling feet to provide clearance to remove the unit. Step 7. Pull unit carefully from under cabinet to access both sides so Door Balance Link Kit is accessible, checking for tension on drain line and power supply line (see Step 3.) as you are pulling out the unit. Step 8. Remove broken Door Balance Link Kit (pay attention to how the rope is positioned around the pulleys; using your phone to take a picture before you disassemble the kit is a good idea). Note-the replacement kit is different in design/appearance (not function) from the OEM part. This should be clearly stated in the "Description" paperwork accompanying the part but it is not. Step 9. Install the new Door Balance Link Kit exactly as the replaced one. It is important to note that there was no spring tension when the broken part was removed so re-attaching the part with the spring attached takes some strength because of the tension. I recently (9 weeks ago) had two brain surgeries; my right arm was paralyzed following the second surgery. Although I am recovering fine, I have not gained my hand strength back completely. I used a screwdriver to stretch the spring back to the attachment point which allowed me to slip the spring into the hole. If you have to use this method or a similar technique, use extreme caution. The spring is strong and if it slips could cause an injury or damage. I strongly suggest that while the unit is out that you replace the other (non-damaged) Door Balance Link Kit. It's had the same wear as the broken and its likely to break soon. Again, if you have the hand strength to remove the spring by stretching it to disconnect it, that is the best approach. But, if you do not have the hand strength, simply take a pair of channel-locks, grasp the end of the spring to stretch the spring to remove tension on the rope and hold it while cutting the rope. Release the tension on the spring and repeat steps 8 & 9 to install the second kit. Step 10. Move the unit back into position to attach the water supply line and then attach the water supply line. Step 11. Carefully reposition the unit back into place checking to make sure the water line, drain line, and power supply are not crimped. Step 12. Once in position, use leveling feet to raise the unit to its proper height while checking to make sure it is square/level. Step 13. Replace the screws removed in Step 4. Step 14. Run the machine through a quick wash before replacing the bottom plate to verify there are no water leaks, crimped hoses, etc. Step 15. Replace the bottom plate (see Step 2.).

Shut off power to dishwasher.Pulled dishwasher half way out from cabinet, careful not to disconnect waterline, drain-line, and electrical connections. Replaced roller assemblies and connected new door balance links to springs as shown in the great video featured on your website. Thank you for the great pricing, speedy service, and the install instructions. I am happy!

Ordered the part. Called my son who brought over his toolkit. Played him the repair video on my iPad and he replaced both Door Balance Links. Door works great now.

Installed the new tub gasket, fairly simple. Installed the bottom door seal not so easy. Leaks are still present.

repaired exactly as your video described......hardest part it getting unit out from under cabinet and back in.

Followed a repair video.

We pulled the unit out and were able to easily see where it broke. We replaced it relatively easy, pushed dishwasher back in; however, somehow the pump seal got broken in the process so now we have to replace the pump. This was totally unrelated to this repair - only can assume it happened when we pushed the unit back into place.

last time this piece broke, I called a tech and $150 to fix. I am not much of a do-it-yourselfer, but this was very easy. Removed to screws. I then pulled out dishawasher from cabinet. Removed plastic piece, replaced part, pushed dishwasher back and put in screws.

Easy, easy, easy. Appliances use to be built with metal parts that did not break as often.

Fairly easy. Undid the two screws on the kick plate. Then used pliers to undo the leveling legs and pulled the dishwasher out from under the cabinet. The dishwasher is hard-wired with extra electric cable. The drainage tube is flexible and there is extra so I did not have to worry about disconnecting anything. I then attached the new door cable link to the spring. Using the Needle-nosed Vise Grips I pulled the cable so I had enough to make the connection on the door piece. Done. Then I put everything back.

The hardest part was pulling the unit out. Ours required the electric to be disconnected. First turn off breaker, then disconnect electric, then remove the 2 screws in the sides that keep it in place (located on top for non-stone counter). Slide unit out. Next remove the spring and connect the loop from the link to the spring. The other end of the spring goes in the hole next to the rear leg. Pull the string so there is enough slack to loop the spring aroung both pulleys and then slide the end over the hook on the bottom of the door. Use the other side as a guide. Slide unit back, hook up electric, replace mounting screws. Turn on breaker.

For some reason I wasn't able to pull the dishwasher all the way out. Had my wife with a smaller hands and arms reached in and attached the spring with the link end onto the dishwaster anchor point. I then put on both nylon rollers. The link anchor point and rope went over the upper roller first. I then struggled and managed, with lots of pulling, to get the rope over the lower nylon roller. All went well with reattaching the water and drain lines. Plumbing in tight spaces is made for small people. This old body does not bend like it use too.
.