66513173K706 Kenmore Dishwasher - Instructions

Remove two screws then the two toe-panels. Use a flashlight to locate spring and the hole in the metal frame near back of unit about an inch off the floor. Look at opposite side of unit to see how the working link is routed. Place correct end of the link over one end of the spring and wrap a piece of tape around nylon clip and spring end (just to save frustration of having it fall off while you attempt to complete this task). Tie a loop in the end of each end of the piece of string you supplied. Loop one loop around the spring end with the link clip and feed the other end of the strings loop out the front of the dishwasher at the bottom near the lowermost pulley. Reach under the dishwasher and hook the spring to the frame. Keep tension on the string and feed the link cord out the front of the dishwasher near the front bottom near the lowermost pulley. Loop the exposed end of the self-supplied string around the center of the flashlight handle. Have an assistant pull firmly on the flashlight/string stretching the spring (not too much to over-stretch the spring, but give yourself a little slack too). Serpentine the link cord around the two nylon pulleys. Make sure the rope side of the link clip is toward the back of the dishwasher. Place the link nylon clip over the metal door lever and into the appropriate slot. Have your assistant slowly release tension on the spring/string. Reach under the dishwasher and remove the looped string from the spring end and remove the string. Replace the toe-panels. I did the right side this way, the left side is up against a wall and I might have had additional problems, but it is hard to say since I did not replace the left link. I thought this easier than removing the dishwasher, inlet and outlet as I have done that several times and it can be a pain as well. Good luck!

The video does a great job explaining the repair. I took the unit completely away from the wall and put it on its side, which I recommend. Only problem I had was getting the new part in the correct orientation to lock... try to pay attention to how the failed pump is facing when you remove it.

I ended up replacing the supply line as well as just moving it around caused a drip leak, guess it was about to fail. Pro tip: don't remove the old line until you have the new line in hand... but that's a story for another day.

Started the rope onto the top holder, threaded the rope around the rollers and using the pilers pulled the spring forward to attach the other end of the rope.

Pretty easy for the parts. Taking the dishwasher out is the hard part. Typically, you should be able to unscrew the 2 screws holding the dishwasher to the underside of the countertop and then slide out the dishwasher to expose the cable assembly - but you also need to unplug the unit (unless it is hardwired), disconnect the hot water supply line from the angle stop (remember to turn off the angle stop) and sometimes disconnect the drain line from the vacuum breaker or garb disposal. You need to disconnect these things so that you can move the dishwasher out far enough to be able to see the entire right and left sides of the dishwasher. Once that hard part is done, you use a hex driver to remove the old cable pulleys, put on the new cable pulleys, and then feed the light weight cable through the pulleys - the end with the big plastic thingie attaches to the door and the other end attaches to the spring. Then you grab the spring and manhandle it onto the back end of the dishwasher chassis (look for the small hole in line with where the cable would line up. Careful as the spring attachment step could result in an injury - Hope this helps.

just move the machine out and replace the string. this site is very reliable and and great company. since the dishmachine door cannot be closed, we first order door strike, ,,,, still doesn't work after installation. and return all parts and order the balance kit, now works fine after. we appreciate your help

Replaced door balance link kit and door opens easy does not squeak or slam down.

The repair itself was relatively easy. I basically only had to remove the two screws that were securing the diswasher to the cabinetry, disconnected the water line and extended the diswasher out approximately 10 inches. I then replaced the part by hooking the new cable assembly to the spring and using pliers expanded the spring so I could snake the other end of the cable through the pulleys and attach it to the door. The otherside was my guide. This part should be modified to replace the two plastic ends with metal counterparts. This would allow the part to have a longer life especially in my case since the plastic end broke and not the cable itself.

Get a piece of stiff wire (medal close hanger) cut a Short piece and take a tool and roll a half circle on each end making the link length you need then attach the lanyard to the spring

Used new seal and glue. Your company was great. However, the part had changed and did not agree with the installation instructions. After calling the friendly person at your company to determine if I had the right part(it did not have a white stripe on it and did not look like the old part), I followed the instructions and it was easy. No leak-happy family.

Disconnect top screws
Pull dishwasher out halfway
Notice how the other side is connected
Thread cord, use pliers to pull spring to connect.

1st pull dishwasher out. attach the new cable to the spring. reinstall the spring on the frame. Use pliers to pull slack in the cable to attach the cable to the door. The hardest thing about the install was putting the screws in the side of the dishwasher to the cabinets.

Received the part. No instructions came with it. Luckily it was pretty simple to figure out. i removed the appliance from under the counter, saw how the part was attached on the other side and simply replaced the other side that was broken. Easy.

Shut off elec. and water. remove bottom plate and 2 screws holding the unit to the counter top.
disconect elec wires to unit and remove water line.
Pull unit out from counter and replace cable to spring the same way as the unbroken side.
Slide unit back and reverse hookup.
My only problem was that the part they sent me was about a 1/2" shorter the the original and the door is hard to open.

My 2 yr old sat on the dishwasher door while it was open. It snapped both the links on the door causing the dishwasher door to drop every time it was ajar. It was a real danger to the kids or to anyone else unaware of the door given its weight.

I ordered the part from Part Select based model and some of the posts that it was something you can do yourself. Park Select was outstanding as got the part next day and got direction from others (thank you). I did not have either side of the door working so no real gauge but finally understood how it worked once I did a search online for a picture.

Recommendation: if both links (rope) are broken, you will need to hunt down the springs on side/back of machine. The part with small hole connects to the spring, the other to the door. Make a reverse S with the rope through the pully system for tention. I did not initially do the reverse S and the part popped of the door once I closed it. Otherwise, easy thing to do and certainly do not need a repair person.....if you need picture, do a search on dishwasher door pully system

Hardest part of job was sliding dishwasher out. Put in wood floors so limited free space. Had to lower fron foot pegs first, then remove 2 screws from top that held unit steady. Once dishwasher was out a good 16" cords were easy to replace. Did not replace bracket that came with kit. Cords attach to heavy duty spring.