WPSQ4160TAAA General Electric Washer - Instructions

To get the old agitator off I first used two pieces of laundry line rope to hook under the fins of the agitator on each side. Next I laid a 5 foot long 2 X 4 across the top and tied the ropes on. I filled the washer with 5 or 6 inches of extremely hot water to help loosen everything up and used leverage to pop the old agitator off. After that I used a socket set to remove the bolt from the top of the agitator coupling and took it out. I then put the new coupling in, replaced the bolt and lined up the agitator and slid it back on until it clicked and locked into place. The washer works great.

I removed the fabric softener cup and lifted up on the agitaotor till it slid off. I then removed the bolt that held the agitator coupling in place. I then worked the coupling off, wiggling it side to side until it slid off. Then I slid the new coupling on and replaced the bolt. Lined up the agitator and slid it back on. Then replaced the fabric softener cup. Job could not have been any easier.

I took the plastic agitator out and checked the agitator coupling underneath. I unscrewed the agitator coupling and looked inside. It appeared that the grooves on the agitator coupling which attaches to the stem had become stripped. I ordered the $6.00 agitator coupling and screwed it back onto the stem. The plastic agitator slipped back onto the coupler and it worked perfectly after that.

First pulled the element 4 inches then removed one screw size 7/16 wrench then put new part alligetor copling

I'm happy I looked at the motor spline while it was running and found it was not slipping. Thanks to GE having a parts list in the compartment behind the controls. I found the part name and number. A quick search of the part number came up with your web site. I payed less for the parts and shipping than driving around town would have cost in gas, much less my time. Thank you

Removed the agetater removed a nut on top of the coupler> Then I removed the coupler put the new one one replaced the nut and the agetater. I receved the new part in two days. Great service I would recomend to a freind and also use parts select again. Thanks very much.

Placed hands fiemly on agitator, at bottom, gave a snug pull and removed it from machine, thus exposing the agitator coupling. The coupling is held to main shaft by 1 bolt(11 mm, I think). Removed it, pulled off stripped coulping, installed new, installed bolt, lined up splines on agitator and slid on untill it "clicked" back into place. All done.

This model did not quite go as in the video on this site. The agitator just pulls up off the coupler. Removed the old, put on new, including new bolt that came with it, snapped the agitator back on, viola!

Removed center hub and agitator with a sharp tug upward ( no tool required) then using a 3/8 drive and 7/16 socket I removed the stripped coupling and replaced with new one. Total repair time was less then 15 min. 10 of then were spent search web page and watching DIY video clip.

This repair is as simple as it gets. Pull up on the agitator to reveal the Agitator Coupling. Remove the old coupling and reinstall the new one. In addition to this, I found the source of a majority of the mold smell inside the washer machine. There was a build up of detergent under the Agitator. A few scraps of a puddy knife, a shop vac, and the odor was gone. The only caution is to be careful pulling up on the agitator because you could potentially hit your self in the face because it will come off fast. Easy, Easy, Easy.

The washer did not Agitate although it did spin. So the motor appeared to be good. I noticed that you could rotate the agitator by hand, that didn't seem right. So I pulled the Agitator off the coupler. Now the coupler can rotate by hand around the spline shaft. I removed the bolt holding the coupler to the spline shaft. The spline shaft looked good. Ordered the new couple and installed it in 10 minutes. I was fortunate that the bolt came off easy. I didn't need to use the motor to assist in getting the bolt free.

The agitator gets pulled up(no tools required).Under the agitator is the coupling which is held on by 1 bolt.I removed the bolt,took off the old coupling(the inside was stripped where the metal gear meets the plastic coupling).tThe new coupling slides right on.Replaced the bolt.Slid the agaitor back on the coupling.WORKS GREAT.5 MINUTE JOB.

Removed dual action agitator to reveal the coupling removed a single bolt and removed old part. Carefully alligned threads and slid new coupling on the shaft and tightened bolt. Put the dual action agitator back on then wa-lah problem fixed. Repair man told me 32 dollars for part plus labor. I fixed it for less than 14 dollars thanks to this site...

Replaced the agitator coupling in about 5 minutes, there was only one bolt and it went back togeather. THANK YOU Parts Select..........

This was an easy fix. I popped off the agitator, un bolted the agitator couplier and replaced it with the new one. The part arrived in 2 days, the job took 2 minuites. No calling or driving around to find the part, no service charge or repair bill. washer working like new!!