LSE1000T Maytag Dryer - Instructions

I followed the instruction video on the Partselect.com website exactly except that I accessed the tensioner pulley through a panel on the rear of my dryer. Very clear and concise.

Removed front door (2 screws).
Removed front panel (the component that held the glides}. that required removal of 5 screws.
Cleaned it and removed old rivets and ends of glides.
Installed new glides and pop riveted them in.
Re-assembled panel and door and all is well.

Thanks

the rear left roller is attached to the dryer with a shaft that has a nut on the end of it, so replacing it was considerably easier than on the right side, which required removing the retainer clip.
Once I got the small back panel off, it was a pretty simple process to replace the roller with a socket - while supporting the weight of the drum with one hand, it took about 5 minutes to replace the roller and re-fasten the nut to complete the job!

I followed the video on the site for the most part. My neighbor helped me maneuver the drum. The noise stopped after the repair that day, but unfortunately it started up again a few days later. Now it is intermittent. I don't know what the problem is :(

Heard a loud squeaking noise in dryer. I changed the belt first which was cracked and worn. The dryer noise did improve, but was still present. I then replaced the rollers and now it runs very smoothly. Should get another 25 years from it. The Instructions for installation were very helpful and easy to follow.

remove front of dryer by unscrewing 2 screws and disconnected 2 wires.took small access panel off back of dryer . supported dryer drum from underneath and r & r old parts.

ps before you put it all back together connect 2 wires from front door and turn dryer on to see if dryer is quiet.if so reassemble dryer in reverse order

Removed the door, then the front panel. Removed the lock plates for the top and tipped it to the rear. Removed the lint vaccuum assembly and the front drum support bracket. Removed belt from drive motor and pulled drum straight out the front. Removed snap ring on support roller shaft and removed old roller. Installed new roller and re-assembled in reverse order. Part fit perfectly and included reasonable instructions.

first i disconect the power , then I
removed the two screws that hold the front door
panel. screws located at bottom of the front door panel.
i removed roller shaft with no. 13 wrench and install new one

Part Select has great step by step instructions on how to repair things. The problem is, I went by what others said probably was the problem. I installed one roller and it didnt fix the problem. So I order the other one and the belt idler roller. Still no fix. The felt and pads are still good, so I take apart the blower and found the problem. I now have that on order. If the rollers and shaft look good, they probably are.

I removed the front panel, drilled out the worn glider plate's rivets and riveted the new plates on. It was easy. However its too late for this worn out dryer. I've replaced, belts, pulleys, wheels, gas valves, ignitor elements, humidistats, lamps, felt rings, and even the whole motor. This baby has just seen too much action and its time for a new dryer.

I removed front cover and disconnected door switch as I supported drum and put a coffee can to hold drum in place and then removed old support rollers and one shaft and then put all compents back together

Removed front panel, removed drum, replaced drum support rollers.

took dryer apart after viewing video. Found problem to be wheel on tension part holding drive belt in place. Used wd-40 to clean plastic wheel put dryer back together problem solved

I first went online for instructions. I then went to home depot to find the part, but they didn't have it. They recommended an appliance store, called them and they were getting ready to close and wouldn't stay open 5 more mins for a customer- so I ordered from you guys. The part came on time and fit perfectly.

I went online and found a video that showed how to do the repair. Although the video showed completely removing the drum; I was able to do the repair by moving the drum to the left and right to access the rollers. By not completely removing the drum I was able to skip reinstalling the belt and re-threading the belt around the tensioners. I found installing the belt slightly difficult the first time I removed the drum when I tried to grease the drum roller. That repair didn't last very long. By not removing the drum the total time to repair the dryer took less than twenty minutes!