JES1133WD01 General Electric Microwave - Instructions

unplug oven from power
remove glass turntable
remove cabinet housing
remove burnt out bulb
order correct part
reinstall new bulb
reattach cabinet housing
install glass turntable
plug into power outlet
confirm light bulb on

get microwave out of cabinet. Took two people because it was very heavy. Used special hex drive socekt because of dimple in the female nut.

DISCONNECT THE POWER CORD and discharge the capacitor
Leave unplugged overnight
Remove vent grille by removing the 2 philips screws
Remove the LED panel by removing 1 phillips screw
Disconnect all connectors that plug into back of the LED board completely
Remove the wires from the switches (3) at the inside edge of the microwave door
Gently remove each switch housing and test all three switches for continuity
Carefully replace non-functioning switches and reassemble the panel
GOOD LUCK

removed the outer case - this was the most difficult part because the microwave is large, heavy, and cumbersome.
once the outer case was off, it was simple - easy to see where the old part was and the replacement was an exact match
it was then just a matter of disconnecting the old burned out part and replacing it with the new one
then wrestling the outer cover back into place and re-fitting the screws.
Microwave is fine now and hopefully good for another 10 years!

To remove the outer cover of the microwave you have to unscrew 7 or 8 Phillips screws but most of them have "secure" type heads, so you need a driver with a hole in the middle, to fit over the pin on the screw head. I had one of those already, so it wasn't a problem. The metal cover is slid between rubberized strips on the front face of the enclosure and needs to be lifted and tugged out quite firmly in order to release it. Once the cover was removed, the bulb can be seen attached to the main frame of the microwave by a soft metal lug that can be bent back by hand to release the bulb and its integrated holder. The wiring harness simply pulls off of the bulb prongs and there you have the charred remains of the original bulb! I tried every appliance store and hardware store in Bismarck, but nobody had this part. When I typed in the serial number on the bulb, Partselect's site came up with exactly what I needed. Replacement was a simple reversal of the process, making sure not to over-tighten the sheet metal screws on the cabinet. Voila! We have light beams again. Thanks Partselect.

I removed the broken wheel and replaced it with the new one. No tools or assembly needed. Took about 30 seconds. The part arrived in about 2 days.

My wife lifted out the broken part and dropped in the new ring guide. It was a direct replacement part that fit perfectly and now works great. She was also the one to diagnose the problem, research and order the part.

-unplug
-remove top and front covers
-unplug wire connectors from heating assembly
-remove heating assembly from metal stand and push out of the way
-remove metal stand from dry
-pull out heating assembly
-install new one in reserve order

Removed cover
Disconnected capacitor from old magnetron
Removed old magnetron
Installed new part
Connected capacitor
Reinstalled cover

Part just snapped into place and wires were reattached.

Unscrewed the control panel (2 screws), lift up and let hang, with a plan screwdriver open bracket holding the switch, unplug 2 wires, replace with new switch, plug in the 2 wires, push switch back into bracket. Then slide on the control panel, put the 2 screws back. Easy fix.

I first read where someone had the same problem. Their solution was a burned-out fuse. I ordered a new fuse...installed it and that did not solve my problem. I revisted PartSelect and read how Marla (from Arlington, TX)solved her problem. I purchased a secondary switch and when it arrived, I made a copy of Marla's instructions and followed them to the letter. I installed the new secondary switch into the secondary space, put everything back together and the oven STILL DID NOT WORK. I had to take the latching panel apart again and test each switch to see if there was another bad one. I found that the third switch was burned out. So I took the new switch out of the second slot and installed it into the third slot. I tested the switches before reinstalling the latching panel. This time everything worked. So I put everything back together, reinstalled the microwave on the wall, tested it again, and everything worked perfectly.

unplugged power
removed main black cover.
located part WB24X10047 and replaced

Removed outer cover, Cash with for Phillips screws as I recall, Then remove six or eight safety screws with Phillips special bit. Pulled bulb, cover back, removed, and replace bulb, back together all set

Remove the top of the microwave, regular phillips screws on sides, torque screws on back. Lift up back and slide off cover. Light bulb socket is easily detached and bulb unplugged and replaced. Slide cover from back lifted slightly so lip will slide into front of microwave, than replace screws. Be sure to unplug microwave before you start.