JBS55DM2WW General Electric Range - Instructions

Real happy on how fast the new part came.
1.Pulled oven away from wall and unplugged the unit & removed baking racks.
2.Removed the back wire cover behind the oven (3 screws).
3.Used the nutdriver to carefully remove the two holding screws inside the oven. Then I pulled the element towards me to expose the wires.
4. Using the pliers, I disconnected the element from the wires.
5. Using my son's help, I had him push the new element leads into the holes in the back while I connected the leads to the wires behind the oven.
6. Replace the two element retaining screws inside the oven.
7. Replaced the rear panel with the 3 screws.
8. Put the oven back in place and plugged it in. The oven worked perfectly!

I turned off the breaker for the oven. I used a electric drill with a 1/4 in socket to unscrew the two bolts inside the bottom of the oven. Then I pulled
out the heating element and slid off one connector and attached it to the new element. Then I slid off the other connector and attached it to the new element. Then I screwed the bolts back. I turned the breaker back on and it worked great.

Turn off circuit breaker.
Lockout (LOTO) circuit breaker.
Pull stove away from wall to access the rear of range.
Remove seven (7) screws from rear cover with nutdriver / screwdriver.
Carefully, disconnect stake-on terminals (wires) from element (may need to use needle nose pliers).
Open oven, remove racks.
Remove two (2) screws holding element in place with nutdriver.
Remove old broken element.
Insert new element. Fasten with screws previously removed. Close oven door. Go to rear of unit.
Reconnect wires to element. Make sure insulation seals around the element.
Inspect for any other damage; repair as may be required.
Replace cover panel and fasten with the seven screws previously removed.

Does not hurt to vacuum and clean the area stove, too.
Push stove back into position.
Remove LOTO and turn on circuit breaker (power)

Turn oven on to highest temp to bake off any contaminates on element. Turn OFF. Let cool. Replace racks a/r. Close oven door.

Invite the pretty girl next door to come over to bake something.... OK, this part is optional.

First step is to unplug the range. Then simple to remove top portion of two part back panel behind controls console, then remove knob and two screws for control, then use needle nose to transfer push-on connectors from old control to new control one at a time, finish re-assembly in reverse order.

Replaced temperature sensor in the oven first ($10 part, always start with least expensive possibility!), but that didn't solve the problem. 5-10 minute repair, not counting moving the range in and out of it's home between cabinets. Next replaced the control board ($90 part) which solved the overheating problem. 15 to 30 minute repair, don't be intimidated by all the wires. Remember to turn off power at the breaker (duh). Order the faceplate graphic ($37 part) because chances are the old one won't peel off cleanly (ours didn't, "I was really careful Honey!!) and the otherwise excellent PartSelect.com website doesn't suggest the part might be needed. Anyway, I saved a minimum of $80 plus Labor by doing it myself. I had the advantage of living about 100 miles from their warehouse and got NEXT DAY delivery from FedEx instead of 3-5 business days. Suggest you order before noon.

Repair: unscrewed the back panel- 2 screw and the sensor and bake element from the inside had 2 screws each. Just stuck them through their old hole from inside to the outside, pushed plug back together. Then screwed back into place, screwed back plate back on. Plugged stove in, turned on the oven and within 2 seconds the bake element was blood red and temp. was up to 350 in less then 10 min. Come to find out only needed the oven sensor -$10.00part but I already ordered the bake element so I went a head and replaced it - cost $50.00. Have a great oven again for less then $70.00repair.

Replacement was extremely easy. The new part fit perfectly and installed very easily without tools. Also, I received the part within a few days

Replacing the sensor was a snap and not as involved as I feared. 1) open the oven door; 2) remove the one hex screw holding the old sensor to the back of the oven; 3) gently pull the sensor, pulling the wiring out to access the plastic wire connector (carefully guide the plastic wire connector through the opening); 4) loop a small piece of wire (stiff enough to form a hook) around the base of the wire connector to keep the wire from falling into the back wall of the oven; 5) unclip the connector and remove the bad sensor; 6) clip in the new sensor; 7) remove your catch wire; 8) thread the wiring back through the opening; 9)position the new sensor and secure with the hex screw; and 10) turn on the oven and prove to your wife you do know what you are doing!

Yeah, so I didn't read the manual the first time we ran the self-clean cycle on the oven. Something about taking the racks out. So these were my little reminder to never do that again. The old racks came out; the new ones went in. Ten seconds. On to the next embarrassment...

the chief of the house(not me) did not let the oven finish self cleaning process and that's why this happend.So for everybody - let it finish you'll get no trouble.But repair itself was easy.1-open the oven and take a racks out; 2-unscrew a support of the element on back wall(2 screws);3pull of the wall and unscrew back panel(5screws);4-unplug connectors and pull the element out of the oven.5-installation is the same but backward 4 to 1.It took me...think less then 4 minutes (I went for a beer).DIY and U save a tons.And BTW those guys from Part Select - excelent service.I'm glad that I found a website like that.It's all ready in my favorites.Thanx guys for quick and very good service.It came what I order and it came in 2(two)days.Keep in touch

The draw pictorial was not very clear. I orderd the two rear supports for the over storage draw, not sure they were correct.
They were correct and the design had been upgraded to add strength to the support.
The draw is now operational..better then ever.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

The heating element in my electric oven cracked, I had something boil over onto the element, cracking it to the point of it sparking. First time I had ever seen this before. The appliance repair shop was going to charge me a small fortune to fix this so I ordered the part online, which it was 10.00 cheaper from here than from any other site. It got to me quickly and took me less than 15 minutes to repair and everything works great. All I had to do was unbolt 2 screws with a ratchet, unplug the element, plug in the new one, and bolt it back up and I was done!

My oven bake element melted one day. I had my husband replace it and for a short while it worked. Then it quit but then our broil element would not shut off. My husband said that it might be the heat sensor. We checked here in town and that element cost over $80. Since we have order from Parts Select before we decide to do so again. When we received the heat sensor my husband replaced it taking out the original heat sensor. This did not work as the broil element still would not turn off. I call the repair man and I found out that the initial melt down of the bake element also effected the main circut board that had to e replaced.