JBS55DM2WW General Electric Range - Instructions

Pulled the oven out and unplugged it. Removed five screws and the back cover. Disconnected the electrical connection. Removed one screw and pulled the sensor out. Installed the sensor and screw. Made the electrical connection on the back, replaced the cover and five screws. Plugged the electrical cord back in and tested the oven temperature compared to the setting. Worked great. My wife then made a small batch of muffins to test it out and they were good.

Consult the instruction guide that comes with the new part. Excluding doing some cleaning while things were apart, the operation took about 20minutes. 1. Open the oven door all the way. 2. Pull back the hinge latch on each hinge. 3. Close the door partially (about broil position). 4. Remove door by pulling so that hinges com out of the slots. 5. Carefully set door face down on a table so that inside of door faces up. 6. With a Torx driver, remove 2 screws at upper part of inside of door. 7. With a nut driver, remove screws at bottom of Door Bottom Channel Trim. 8. Lift inside of door off, being careful not to lose the spacers that are behind the door panel at the upper part of the door. 9. With the nut driver, remove 4 screws that hold bottom trim to the side trim pieces. 10. Remove the old trim and replace with the new. 11. Align the left, right, and bottom trim pieces. 12. Reattach the 4 screws that hold the bottom trim to the side trim pieces. 13. Carefully replace the inside door panel, making sure the spacers are aligned properly between the main door pieces. 14. With the Torx driver, replace the 2 screws at the upper part of the inside of door. 15. With the nut driver, reattach the bottom screws at the bottom of the trim piece. 16. Carefully reinsert the door hinges into the slots (the door must be in the approximate broil position). 17. When hinges are properly inserted, door may be opened all the way. 18. Push the hinge latches back into hinges to secure door to oven.

I pulled out the drawer and inserted the new support. This one inserts into the back of the drawer as opposed to the sides. I had ordered two of the replacements even though I only needed one and decided to replace both. I think it was a good move as the drawer works better than when we first got it. Just one simple screw made it complete.

Safety first * Unplugged 220 VAC from outlet. Removed shield cover screws with 1/4" hex nut driver (5 screws). Removed all 6 silver screws from terminal block with 1/4" nut driver, freeing all wires. Removed the green ground screw and ground bracket from center terminal. Cut away (using the drill) melted original terminal block plastic to access the 2 black 1/4" nuts holding original terminal block onto appliance. Discarded the original damaged terminal block. Attached the new terminal block, aligning the mounting holes and the terminal block the same way the original terminal block was lined up and re-used the black 1/4" nuts (original used because the replacement package did not include new black screws). I bought a new appliance cord, since the original cord overheated. Reattached all wires using the 6 new silver screws. Start with the middle terminal by attaching the appliance wires and the ground bracket. The ground must be attached to the bracket and the bracket bridges between the terminal block and the range body. Reattached shield cover. Plugged in appliance. Note: it doesn't matter which outside wire attaches to the outside terminals (both are hot), but the middle wire (neutral) must attach to the middle terminal. However, the ring terminal should be flush on the terminal block so you don't bend the ring.

Removed the oven door and shelves. Moved the oven out from wall, so that I could access the rear panel. Unplugged the oven. Removed the five (5) screws holding the rear panel in place and removed the panel. Disconnected the sensor at the connector. Removed the screw holding the sensor in place inside the oven and removed the sensor. Theaded the sensor wire through the rear of the oven wall. Installed the sensor and screw to hold it in place. Snapped the connector from the sensor to the mating connector at the rear of the oven. Installed the rear panel. Installed the five (5) screws to hold the panel. Plugged the oven back in and slide the oven back to the wall. Installed the oven shelves and the oven door.

1) REMOVE ELECTRIC PLUG FROM OUTLET. 2) Pull oven away from wall. 3) Remove the 3 machine screws holding in the top piece of sheet metal. 4) remove top piece of back sheet metal 5) pull knob of the front of the switch. 6) remove the two screws holding the switch to the front of stove. 7) remove wires (needle nose is helpful) one at a time and put them in the same location on the new switch. 8) put new switch into location on the stove and screw in the two front screws. 9) replace sheet metal on the back and screw in the 3 machine screws that hold it in. 10) plug in stove and move it back into position 11) put the knob back on the front and test it to make sure it works ok. 12) be sure to remove power if you need to do open the stove again to correct anything.

Removed old racks and replaced with new racks.

Unplugged the oven, took out old element and replaced with new element. It was really simple and easy to do, didn't even need my husband who is not mechanically inclined.

First I removed the two screws that hold the element in place. I then went to pull the element out and one of the wires touched the side of the access hole. There was a spark and the electrical breaker tripped. (Remember to always shut the electricity off first). Before I put the new element in I took off the access panel on the back of the range, slid in the new element, attached the two screwd that hold the element in place. Then I went around to the back of the range and re-connected the wires from that location to make sure there was nothing around the wires that would spark. Put the access plate back on and I was done.

My stove would not heat. I could see that the bake element had a hole burned through it. Found this website. I was confused about what part I needed so I called the phone number and the girl was very good at locating exactly which element my stove needed after I gave her the stove make and model #. I ordered the part on Thursday afternoon. The part arrived on Saturday afternoon.

The hardest part of fixing it was finding the correct screw driver socket thingy (I'm not a technical person) to get the screws off with. Thankfully my neighbor had what I needed. I pulled my stove out from the wall (primarily because I needed to clean under there) and unplugged it. Unscrewed the screws, pulled the old element out until I could see the wire connections. I used clothes pins to hold the wires from going back into the stove once I unhooked them from the element (another tip I learned on this website) and simple slipped the wire connectors onto the new element, pushed it back into place, put the screws back on, plugged it in and TA DA... was baking a pizza in no time.

Very very VERY easy repair!!!

Took out the 2 screws,Pulled out the stove
Took the back off ,took the wires out of the little place where they fit in,Removed the old element.
Put the new one in Fitted the little thing which looked like a alumium flat piece back where we took the old one out.Put the back back on cut it on wheepe In business.Also the new element came here faster than I thought it would .I,m a 71 yearold grandmother.Pretty simple.

My husband actually did the replacement but I did all the research online to find the right part. I wasn't sure we'd find it for our old stove but luckily we did and it works fine. Thanks for the super fast service!

My exact model number did not appear in the listings, nor were the oven rack measurements clearly stated in items offered. I sent an email to customer service, received an immediate response with the correct answer (re: which part would fit my oven), ordered this item, and had a shipment arrival within days. The racks are a perfect fit, and they look great. The price is less than any other site I investigated.

recieved part the next day. looked different but I followed instructions and the part worked perfect.

replaced lights in refrigirator and freezer