GTWN4250D1WS General Electric Washer - Instructions

Surprisingly easy. I took the screws off, then pulled off the drain hose. I then inserted the new hose, and put back the screws. Amazing quick!

Watched the video. Followed the instructions. This has to be one of the best sites I have ever encountered. Even a caveman could fix the problem after watching the video.

Reach down and grab the base of the agitator with both hands and yank up with slightly more pressure on the left or right, whichever side you prefer. This will break loose the holding clamps/pull straight up. To re-install: align slots and push down until it snaps. Simple as that.

The hardest part is lifting the washer to get a the bottom. Disconnect the power, shut off water. Disconnect hoses and drain hose. Move washer from the wall about 2 feet. Tilt up front of washer. I used 4 12" long 8x8 inch lumber, lift washer….place one on each from corner. Lift again, place 1 more 4x4 on each existing 4x4. Now remove the belt off the 3 pulleys. Use the flat blade screw driver to remove the C clip holding the Pully on the shaft, with the flat bladed screw driver and hammer. Once the C clip is off remove the metal washer, pulley, plastic lock (apart of the bottom of the pulley & the thrush bearing and it's washer. Using the parts supplied (the "new thrush bearing is a bearing and washer combined) replace as you removed it. Thrust bearing, pulley, washer and, c clip. I tapped mine on using the flat bladed screw drive……becareful not to break it (they did supply 2 for me in the repair packet) make sure he c clip is secured. Lower the washer after removing all the tools from under the washer, by reversing the lift sequence. Slide the washer in place. Connect the hoses back up. Plug it in.Reconnect the drain hose, you should be good to go.

turned off off water supply, unplug plugged washing machine and removed back panel to access triple water valve. removal was easy that took about thirty minutes.

Pull hose out from wall and drain water into bucket. Remove two screws from back of washer holding on the clip. Pull hose out from washer its in there about 3 inches or so . If you order a new clip will make this even easier it's only $3.87 and I didn't realize I needed it. So, I just cut the old hose with a small saw near the clip so I could remove it and reuse it. Just slide the clip onto the end of the new hose - it fits into one of the grooves-I just made a note of where that was before removing from old hose. Then replace the two screws on the clip going to the back of washer. Put other end of hose into pipe in wall.

This is a normal condition; the old bolts are self-tapping so simply align them well, I used a drill-driver to get them started and completed tightening with a socket wrench. (Also the new drive shaft assembly comes with a tub seal, so you don't have to order a separate one.) I do think it would be better if the drive assembly came with 4 new bolts.
The instruction video was immensely helpful, Thank you.

I had to insert a broom stick to keep the drive pulley from rotating as I hammered the tub nut loose.

2nd tip, my washer has the standard agitator with the glued on cap; it was unclear if I needed to remove it; you should clarify that this is not necessary, that one must only pop up the entire agitator; I used a shipping strap looped under the agitator and over a 2x4 across the top of the frame, tightening until the tub was raised a bit and then a gentle pop down on the tub and the agitator easily popped off.

Could not complete repair. The pulsator was rusted on the shaft, used wd 40, finally pried off the shaft. The hub nut was so corroded on the shaft I could not remove it. Reassembled the Machine.

Removed control panel removed old pressure switch installed new switch replaced control panel plugged in washer.everything worked the way it is supposed to.

Popped the front cover off and found a small hole was in the drain hose going to the pump,used pliers for one clamp and nut driver for the other clamp,removed bad hose and installed the new hose,ran water pump after putting some water in the tub,checked for leaks,put the front cover back on,that was it.

Pried the front cover off the washer and then rotated the tub around for easier access to the hose clamp. Used screwdriver on hose clamp then detached spring clamp from pump inlet. Reversed the procedure for repair!

First I had to remove the front cover to the washer.
Then it was just a matter of using the nut driver to loosen the clamp holding the hose to the tub portion, and a channel lock for the clip on the drain pump. Pull the old hose out, do the same thing vise versa for the install... Only hard part was the clamp on the drain pump was being a little difficult (but no big deal).

Unpacked the agitator from the box. Manually pulled off the old agitator and snapped on the new one. Total repair time was under 2 mins. Much better than a $120 service call.

I removed the top cover , then unplugged all the wire connectors. I then replaced the control board and reassembled the wiring and cover.