GTW460ASJ6WW General Electric Washer - Instructions

Following directions from a Youtube video.

part select help

Replacement was extremely easy:
1. Shutoff Water Valves
2. Removed hoses from Washer
3. Removed two screws to get control unit off.
4. Removed wires to valve assembly.
5. Removed Screw holding assembly in place.
6. Removed temp sensor from assembly.
7. Unit came right out and reversed the process for replacement Unit.
8. Very easy...

unplugged old part plugged in new, took about 2 minutes.

this is a great web site, I didn't have to wait for a serviceman to come. and maybe not have the part and come back again. ........thanks

The most important item I learned is the original lid switch is no longer available. It has been replaced with the entire Lid Switch Assembly. I read the new switch is magnetic versus the old which was mechanical. The kit comes with everything you will need (switch, wiring harness, lid lock bezel and instructions). I found the written instructions to not be the easiest to follow. However, I found someone had done a YouTube video on the replacement which made the repair easy (under 15 minutes). Although I did the repair by myself, a second person would be handy to hold the washer cover and controls while changing the wiring harness. When testing the new switch, remember to test during the Spin cycle.

Upper portion of auger spins on bottom portion so they need to be locked together with a screwdriver to twist off counter clockwise. Good instructions here: https://m.youtube.com/watch?v=Qr4GzTJBho0&vl=en. Someone needs to hold the tub while another uses the strap wrench to turn the auger counter clockwise. Should pop off with a bit of force. New one pops on easy.

Attached the lid striker with 2 screws to hold it in place

Turned washer on to its side. Removed belt cover, three screws. Removed old belt. Cleaned both pulleys thoroughly, removing all traces of oil. Cleaned grooves thoroughly on motor pulley with small screwdriver. Installed new belt. Replaced cover. Turned washer upright.

I just took old one out an put new one in

Extremely easy. You will need a helper to make it easy. The best directions are on you tube.

first disconnect the electric power cord. Disconnect the incoming water lines. Tip washer up or better yet flat on the floor where bottom is completely exposed. Remove bolts holding guard over belt and motor. remove bolts [2] holding clutch arm into plastic bearing, remove old belt will slide off pulley, remove bolt holding pulley to shaft, calls for a puller but I applied pulling pressure while working back and froth; no problem but could have been. chance clutch bearing and reverse the process to working order. I would recommend wearing cloth or vinyl gloves once the guards are removed for the pulley and old belt has a lubricant that is somewhat messy but cleans up easy.

REALLY easy-
Just unscrewed the two screws with a Phillips, slid the old one out, the new one set in perfectly, and used the same screws to hold it in place. 2 minute task total.

IF you do the same repair, SAVE THE LITTLE O-RING that is inside the old part where the temperature probe stick in (If that is indeed what it is). It's chrome in color. New part does NOT come with that O-ring

1 Disconnect power 2) Cut water supply to washer 3) Disconnect water supply hoses from supply.
***if pump broke with water in tub, remove water from tub. 4) tip machine onto it's front side 5) remove hose clamp of exhaust hose & then remove exhaust hose from pump 6) Remove pump with socket/ratchet 7) disconnect pump electrical plug 8) tell old pump to take a hike & throw in garbage 9)Iinstall new pump 10) Do steps 7—1 in reverse order to put back into business.******Be prepared to do it again in 6 months; I havnt had good luck!

Emptied the washer, took the back cover off, tipped it foward, unplugge the old pump, remove two mount bolts. The replaced the new pump. The new pump resolved the issue.