GDT635HSJ4SS General Electric Dishwasher - Instructions

Followed a u-tube video to remove dish wash door assembly to get to the control board . Not too hard if you are mechanically inclined.

Removed the door to get to the UI control panel. Followed the instructions to set the jumpers to my particular model and put it back together. Fixed the issue and worked perfectly.

Simply put it on and twist it to lock in place. Took all of 3 seconds

Took it out of the box and set rollers on track
rolled in place ALL DONE

After hours looking for problem. I tried cleaning door gasket. Did not stop leak. Looked at lower water spray arm and it was split. It is literally a 2 minute repair to remove and install. Knock on wood, no leaks in the last 10 washes.

It was relatively easy to fix. I unscrewed the mounting screws from the cabinet, slide the dishwasher out to access the pump under the dishwasher, I did raise the dishwasher on the left side and steadied with a stool to make access to the pump fitting easier. Then I loosed both clamps at the ends of the hose ie. from the dishwasher pump and the connection to the sink drain line, pulled the clamp off of the end that connects to the pump and placed it on the new hose connection, I removed the old hose, connected the new one and tightened the drain line connections. I placed the hose in the hose holders on the side of the dishwasher slid the dishwasher back into place and secured it in place with the mounting screws.

Unplugged power.
Shut off water supply.
Remove the kick panel.
Unscrewed dishwasher from under cabinet and side screws. lower feet to reduce tension.
As you slide the dishwasher out, be sure all lines (Drain, water supply, electric are free to move with dishwasher.
I was able to hold the dishwasher at an angle to easily get to the valve. After removing the the valve, i screwed the new valve back into place. I removed the Line between the valve and Dishwasher. Putting the line on the new valve. I removed the water supply line from the old valve and installed it on the new valve.
Placed the dishwater back in place and screed it back in. I ran the cycles. everything works!
I replace the kickpaner a couple of hours later. Check to make sure there were now leaks.

So after noticing some horrid food waste build up in my 9 year old dishwasher, I determined it wasn't heating the water during the wash cycle. I came on here to check how to replace the heating element and was surprised when the flood switch was instead strongly recommended as the first repair step.

I ordered the part, and prepped the dishwasher for the repair (Pro-tip: Clothes pin attached to the bottom of the flood switch wiring harness ensures it doesn't slip down below the opening during the part swap!). The part swap and reassembly only took 5-10 mins or so after prep and dishwasher is now heating water and running great again. Many thanks to partselect.com for the detailed installation guides/videos and the parts recommendations!

It took a little googling and YouTubing to find the problem and solution, but once we had this UI board in hand, the installation was simple.

Most of the labor and little bit of struggle was taking the dishwasher door apart to get to the UI board.

Make sure to follow the instructions in the package to configure for your model, which was straightforward and simple enough to do.

Once the door was back together and reinstalled, she worked like a dream. The display also seems brighter to me. We haven't had the "random singing" that the dishwasher was doing before the original UI board went out either.

You can do this fix!

Simply pick the basket up to slide wheels onto axles and push in until they lock in place.

the design of this part is easy to break when closing the top rack.

there is a hub that clicks in place and a spinner within this that makes the water spray evenly on the top of the tub of the dishwasher

the part broke when closing the rack [a dish too tall hit it]

it took less than 5 minutes to replace as the part just clicks into two edge spots i did this without removing the rack or even looking into the tub all by feel

My son did the repair, I ordered both latch and striker, only needed the latch...only took him a few minutes to remove the old and install the new and works just fine

Popped the old one off. Popped the new one on. Easy as that.

I took out the old one and simply inserted the replacement. It was an exact replacement part and thus a perfect fit. Dishwasher is working fine now! Cost was around $40 (shipped) which I thought was reasonable.

Unscrew the upper and side holding screws. Move dishwasher part way out. I didn't need to disconnect the water or electric. Make sure the electricity is off. Remember your working around water. Take off the bottom plat removing two screws, Remove broken cable pulley and replace new. Buy two since your their you might want to replace both. Have fun! It's duck soup.