FWTR445RFS1 Frigidaire Washer - Instructions

First of all unplug your washer from the power supply and turn off the hot and cold water supply. I removed the front lower panel of the washing machine with a philips head screwdriver. Next I removed the plastic pins holding the right side shock obsorber. This was a little difficult because the upper pin is in a tight location and there' ... Read more s not much room to push the pin out. I just used the flat end of a screwdriver and slid it in place. The pins take some effort to push out, mainly because you have to hold the little tab on the pin down while you push it out. The replacement shock seems to be better constructed. I just put a little Vaseline on the new pins to help them slide through the metal sleeves on the ends of the shock. You also have to pay attention to which way the sleeves go into the shock so you don't push them out when you install the shock.

Replacing the pump was pretty easy. The pump is right there in front fastened to the bottom plate with two philips head screws. Have some towels ready, because if there's water in the drum or hoses it's coming out when you remove the hoses. Take a pair of pliers, or channel locks and open the hose clamp on the big inlet line, coming from the drum and slide it back so you can remove the hose. Then do the same for the outlet hose on the left side of the pump. It's easier to do this before you take the pump off the bottom plate. Once the hoses are off, remove the pump with a philips head screwdriver. While you have the pump out of the way, feel around inside the square reservior at the bottm of the big inlet hose to make sure there's nothing in there that might get stuck in the pump. A large bobby pin had made it's way into my pump and damaged it. It had fallen back down in that reservior, so at first I couldn't understand why the pump wasn't working, til I found it in there. Insatllation of the new pump is just reverse of disassembly. After that turn your water supply back on and plug in power. You might want to cycle the machine before you put the front cover back on to check for leaks. Good luck!

1. Removed bottom cover - torx driver and drill adapter.
1.5 Unplugged machine and disconnected electrical supply to old pump.
2. Removed flexible hoses with wrench.
3. Removed pump base from machine with torx driver - the hard part as small hands are needed
4. Connected new pump to machine base with torx driver - ... Read more hard again.
5. Connected hoses - wrench
6. Connected electrical supply and plugged in.
7. Tested pump - very quiet again.
8. That's it! Don't pay a service guy $250 to do this. Buy the pump and do it yourself!

-Unplug machine and remove all water connections
-Remove back panel with power phillips screwdriver
-Removed some rectangular circuit box in the way of getting to one shock absorber (3 screws)
-Remove old shock absorbers with 1/2 inch socket (suggested in accompanying directions)- this took 2 minutes
-inserted new shoc ... Read more ks as directed...this was the most difficult part, but used a hammer to bang into place.
-reinsert and screw down circuit box (or whatever it was)
-reattach back panel
-reestablish water hose connections
-plugged in and was in business
-had ordered a washer/dryer set for $1700 (at my parent's urging) and now can tell Sears to go pound sand!

Perfect replacement. Fast shipment. Price was less than "original" part would have cost.

I had called a repair man; and fortunately he never returned my call. After reading many of the reviews involved with the same problem, and wanting to use my washer, I decided it was easy enough to give it a try. And so it was. 2 screws in back removed the cover; and 2 screws in the front of the washer permitted the removal of the affec ... Read more ted part. Removed three "plugs" from old; put them on the new part; replaced it back in the washer, and replaced the two front screws, which held it in place. Replaced top, securing with the two screws. And surprise - surprise -- the washing machine was working again! Your reviews were so helpful and encouraging --- that this really old lady decided to try it --- and like they all said "It was really easy to fix."

I removed 2 screws from the the top back of top. Removed the cover. Removed the 2 screws holding the door lock assembly.Removed the door lock assembly, disconnected the 3 wiring harnesses. Connected the wiring harnesses to the new door lock switch assembly. Installed the new unit in the door lock, reinstalled the top.Done.

I found and ordered a new latch from Partselect.com. After a few days I received the new part. I used a square drive screwdriver to remove the two screws that retained the broken latch, put the new latch in place, and reinserted the retaining screws. The job couldn't have been easier.
I couldn't be happier with the quality of the pa ... Read more rt or the speed of delivery and wouldn't hesitate to order from Partselect.com again.

I removed the 2 screws holding the broken door catch in place, and attached the new door catch with them. The repair could not have been easier, and now the door works great.

Also, I ordered the part, and it arrived via FedEx the next day. That greatly exceeded my expectations!

I was having issues with the door catch. It looked worn, so I ordered the $10 (plus $13 shipping) part. Replaced the part, same issues. Figured out the hard plastic door catch was just not designed large enough to keep the door (a.k.a. lid) closed. My brilliant brother suggested I just put a piece of masking tape on the tip of the door ca ... Read more tch to enlarge it. Guess what? It resolved the problem. I could have saved $23 and used masking tape that was left in the garage by the previous owner of my house.

2 screws out then 2 screws in.

Very easy, took off the lower front cover (two screws). Pump is on the right side up front. Took the two screws out that hold it down, unclamped the clamps inlet and outlet hoses. Put a towel under and around pump to catch water befor pulling pump out. Installed the new one in revers order.

I used a shop vac to remove the excess water which would not drain from the drum - this is key to not flooding your laundry room. I removed the 2 machine screws at the bottom of the front panel. The panel removes easily which exposes the pump at the front lower right of the washer. I disconnected the electrical connection on the pump. Usi ... Read more ng the shop vac I slowly removed the hose connectionns at the suction and discharge sides of the pump. Following the disconnect of the hoses screws hold the pump to the base of the washer. Upon removal of the old pump you re-install the new in the reverse order. One item to note is that I purchased 2 hose clamps to replace the spring loaded OEM clamps for the hoses - this greatly aids in reinstallation. Re-install the front cover and you are ready. Total time to repaire 30 minutes - very easy!

I followed the instalation instructions provided with new parts. Getting the mounting pins out was relatively easy However, the shock on the right, behind the pump, was a bit more difficult to remove than the one on the left. I took the rubber drain off the pump in order to get at the pin behind the pump. The new replacement shocks came w ... Read more ith the plastic bushings inserted in the shocks in alternate directions. The original pins were all inserted into the bracket / shocks from the rear so when I installed the new shocks I reinserted one bushing on each shock so they we both oriented in the same direction. The instruction says to be sure the mounting pin is pressed from the side with the busing collar. It seemed strange the shocks came that way, with no mention of switching them. The most difficult part on the installation was pushing the pins back through the bracket and shock since there was no easy way to push the pins in from the rear. I used a large channel locks on the left side, but the right side was more difficult with all of the obstructions. I finally was able to push in place with my bare hands but was very difficult. Sorry to say the new shocks did not cure the vibration at all. I was very careful to make sure the machine is level. I'm not sure if there is a cure other than replacing the machine.

Thank you for this web site! A friend suggested the problem being the drain pump, but I was not convinced as the washer would still drain on certain cycles. I took the chance and ordered the part after reading like stories on this website. For the repair: don't forget to lay towels down or have a shop vac ready to collect the water in t ... Read more he lines! The clamps were somewhat difficult to manage as the space is tight, but I did get them off with a medium size adjustable wrench. Getting them back on was a bit more difficult; I gave up on one and put a new o clamp on. It's metal, so I'm sure I would have been better off using the plastic-coated factory clamps.

The door catch on the washer broke, and I had to epoxy the broken catch to finish my laundry. I looked for the part online, and PartSelect not only had the part but had a photo of it as well. I was very impressed with how quickly the part arrived, and within 15 minutes the repair was complete. Thanks for having the photos and getting t ... Read more he part to us so quickly.