DBVH520EJ4WW General Electric Dryer - Instructions

I first unplugged the unit, opened the top, disconnected and took off the control panel, took off the front panel to determine the source of the squeaking noise coming from the Dryer. I saw that 3 of the 4 Front Drum Glides were gone and the drum had worn away significant amounts of plastic from the Top Bearing Assembly. I purchased the Top Bearing Assembly and a set of 4 Front Drum Glides. Disassembled the damaged parts and reassembled with the new replacement parts. The reassembly took less than 20 minutes. I plugged in the Dryer and viola! It works as good as new.

pull top and front of dryer (6 screws), take belt off drum and pull drum out the front of dryer. Take the three star head screws out of stainless heat vent inside of drum and take old bearing housing out of back wall of dryer housing. Pretty much self evident putting everything back in, some trouble installing new bearing housing in back wall of dryer, screws are hard to turn in by hand (new hole). Vacum inside of dryer housing, install everything the way in came out, , plug it in and WA-LA.

Removed panel to access the interlock switches. There were two. The button on one switch was fine and the button on the other would not depress. Ran a continuity test and it failed. The switch also had a burnt smell

Took out interlock switch (two leads) and replaced with new one. As simple as that.

Pulled the unit all apart to replace the rear drum bearing. Also replaced the front bearing. Works like brand new. Easier then I thought

Pull the two scews to release the top of the cabinet. Pull the two screws to release the face of the cabinet and tilt out.
Take the old slide out and install the new ones.
Put it back together.
No more squeeks
My wife thinks I'm a genius...

Opened dryer door and removed two screws that held front of top panel on. Lifted top panel off and removed two screws that held front panel to side panels. Tipped front panel forward and replaced all four slides. Cleaned everything off and put back together. Works great again. Thanks for this site and for others that have done these repairs before and posted their stories.

Worn out top bearing plastic part and worn out felt. Removed top part of the front where the dial and buttons are, then the top, then the front where the parts I was replacing were. It was overall easy and didn't require a cdertified repair person. These were parts that were worn out. I am dissapointed in the GE product. It is only 3 1/2 yrs old and already worn out. Poor design and poor quality parts. I will look at other brands next time when replacing the front loading dryer and washer. Overall a faril;y easy repair that most mechnicaaly oreinted person can do. Also thaks to partselct for the diagrams which helped tremendously with meticulous parts.

Easy repair, but did take a little longer than anticipated due to the extra cleaning that I did while the dryer was disassembled (highly recommend). First, unplug the power cord. Then, open the door, and locate the two screws in the upper corners, and remove. This will allow you to remove the top cover. Be careful and work the top panel up and down to loosen the control panel tabs, and set aside top panel. Next, remove the two screws located near the top on the inside of the front panel. Removing these two screws will allow you to lean the front panel forward, lift up, releasing the tabs holding the bottom of the panel. Be careful when you pull the front panel from the dryer as you will need to lift the drum off of the front bearing which is attached to the front panel as it is removed. You will also need to use your needle nose pliers to remove the wires prior to setting the panel aside. The wires are straight forward and power the light at the top, and the safety door switch. I always take a picture with my phone's camera just to validate when I re-connect them. Reaching underneath the drum you will be able to feel the belt and belt tensioner pulley. With both hands under the drum, use one hand to push the pulley to the right, releasing tension on the belt. Move the belt out of the groove, and let it hang freely. Now from the top of the drum, bump the drum to loosen, and remove from the cabinet. It is a tight fit, so you will need to spread the sides slightly in order to remove the drum. Next, remove the 3 screws holding the heat diffuser in the rear of the drum in order to remove the rear drum bearing. (Tip: It would be nice to have a helper hold the new drum bearing in place when starting the screws, and it also helped to tighten each a little at a time to keep the new bearing flat as it was drawn up next to the drum.) Tighten the screws holding the new bearing in place. Next, remove the 4 small screws holding the heating element housing to the rear of the dryer. (Tip: Rather than disconnecting the wires, I used a bent coat hanger to hold the housing while I removed the bearing retainer and clip from the rear of the housing.) Remove the 4 screws holding the bearing retainer and clip, and replace with you new part, paying close attention to the clip's position, and tighten. Replace the housing to the rear of the dryer. (Tip: Now is a good time to familiarize yourself with the belt and tensioner pulley for reassembly. Also, it may be a good idea to look at your belt, and replace as needed.) Next, reinstall the drum and insert the new bearing shaft into the new bearing housing. Using both hands again, reach underneath the drum, locate the tensioner pulley, and belt. Push the tensioner pulley over to the right, and move belt over the pulley on the motor, and behind the tensioner pulley. The belt should be tight. If not, inspect to ensure that the belt is over the motor pulley, and the tensioner pulley. Next step is to reinstall the front panel. I also spent the extra money and replaced the front drum bearing, and slides. Please note that the green slides are on top, and the white slides are on the bottom. Lift the panel over the tabs, lean forward while lifting the tub, resting the tub on the front bearing. Reinstall two screws in the upper corners, and tighten the front panel back in place. Now is a good time to turn the drum to ensure that the belt is in place, and that the drum turns correctly. (Tip: If your dryer is equipped with a light, you may also want to replace the bulb in the front panel (if needed) prior to attaching the front panel.) Reinstall the top panel by aligning the tabs in the control panel with the top panel, being careful not to bend the tabs. Next, open the front door and use the 2 long screws to reattach the top panel to the front panel. Plug in power cord.

I watched a video and followed the video instructions. Spot on and fixed the problem. Very easy repair.

Replaced front plastic bearing and bearing slides for less than $90.00. The repairman from Sears said it would cost at least $300.00 in parts plus labor to repair it, he suggested buying a new dryer (what an idiot). This was a very easy repair, I found instructions on YouTube. 15 minutes and a Phillips’s screwdriver is all that it took. The dryer runs perfectly with no shudder or squeal.

My washer and dryer set are stackable. First I had to take the dryer down from atop the washer. I thought the problem was the rear bearing.
When I received the new rear bearing I watched the video and proceeded to take the unit apart and then I realized the top bearing, slides and the felt seal were completely destroyed so I ordered the rest of the parts I needed It took about 5 days to get the parts and less than 30 min to install. The videos were a big help. I had no Idea what I was doing and was surprised how easy it was. It was a Big savings over buying a new dryer.

I followed the very easy YouTube video and got the three tools I needed before beginning. I started with removing the parts of the dryer and that was extremely simple by following the steps in the video. Took the door off last, located the parts that need replaced that didn't require any tools at all. Then put all the parts of the dryer back on in the order I removed them. The entire process was about 25 minutes but I would say I spent more time really cleaning the dryer and lint build up than actually doing the repair. Video was super thorough and easy to follow, I've never attempted any kind of repair of an appliance and I'm extremely happy that I had the video and the parts that were recommended to fix my problem, were spot on. Saved me hundreds of dollars and time. Thank you so much!

One thing to note that I didn't immediately notice. Upon removing the front panel, there is a chance the drum will stick and when you separate the front panel from the drum, this will pull it from the rear bearing. We did not initially realize this was the case until the dryer was back together and would not run. If there is any resistance, we found the easiest way to solve the issue is to lay the dryer supported on its back, then everything slides in and out. the second time through from start to finish took less than 10 minutes. I loved the videos and the parts. I tried cheating and getting the parts on amazon, and wound up buying from this site anyway and paying even more to have it rush shipped.. All in all super glad I did it and didn't buy a new dryer, I think we can tackle replacing anything on it at this point.

Son found out where the bulb was by using YouTube. I googled lamp for model number and your website came up. I ordered the part, it arrived promptly, and my son installed it.