ARR620 Amana Range - Instructions

I didn't. Don't know how to get to light bulb to change it for this specific model

TURNED OFF POWER TO STOVE Removed 5 Knobs, 2 screws that held bad switch.
Removed 4 screws and lifted panel up and forward to expose switches. Adjusted spring tension on knob stem to hold knob ( stem in new switch slightly smaller) removed wire from defective switch one at a time and fastened to new switch in sequence. Reassembled and turned power on. Defective switch had stuck contacts making it full hot.

Removed the door and old hinges and reinstalled the new hinges and added some screws to better support the door ( it was bending a little at the middle and the door would not shut all the way. Now it works fine.

ordered part -got it the next day- stalled as long as I could then opened oven removed racks-used screwdriver to loosen screws in bracket holding element on- pulled out element-used pliers to take off wires in element-thew old element as far as possible-reversed procedure to put in new element-replaced rack-received praises of all afffected-the end

My elements just plug in so all I had to do was pull them out and replace the drip bowls. They fit perfectly!

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

i really wanted a new stove, but budget wouldn't permit; so just had to insert the new ones and they work great with level cooking.

To replace a bowl lift burner slightly (1") then pull gently until it comes out. Remove bowl, replace with new bowl. Insert burner by pushing gently yet firmly, place down into clip.

To replace indicator light, remove panel from back of stove.
Locate light indicator switch, push indicator lens through front of stove, hold in place (may require a second person) slide switch unto the nub of plastic on the indicator switch. Repeat for each broken indicator lens.

took out the old ones and replaced them following the instructions provided by you. thanks

Received part after one working day and was installed
in five minutes.. Would recommend as a do it your self
project with the support of PartSelect.com

left side hinge was broken. I removed 2 screws to release the old hinge and replaced it with the new hinge.
Part select.com made it easy to pick out the part from the diagram supplied on the web site. After it was ordered it arrived 2 days later.

Unplugged oven. Took screws off top backside cover. Pulled off oven knob. Pulled wies off backside of krc electric module, Making sure to remember the order of the wires. Took off four screws on the module and pulled it out. Pulled off the touch pad plastic from the old module. Put old touch pad plastic on new module. Replaced new module with the four screws. pushed wires back on. Also, replaced left side back guard end cap, by unscrewing the three screws that hold it. I then replaced top backside cover. pushed back on oven control knob. Plugged oven in and tested it. Now its as good as new.

I removed the two screws and pryed out the old hinge. I then put in the new hinge. The new one fit well. I went to screw it in with the supplied screws. The screws not only did not fit the hole tapped in the hinge (too big, different tread) but both screws were different from each other. They were different sizes and different types all together. I tried re-using the screws from the originol hinge but they also did not fit. I then got my own self tapping machine screws and finished the job. This job should not have been that hard. If they had supplied the correct screws, It would have taken all of five minutes.

replaced old, worn blocks with new style surface plug in block kits - all 4 burners. Completely resolved the problem at very low cost (less than $50.00).

Simple to do. Remove old element, remove screw holding socket, cut the socket wires with 2 inches to spare, assemble the newsocket and wires with heat shrink tubing, strip range wires, apply the wire nuts as instructed and shrink the tubning with a heat gun.

Screw on the socket to the range. Shut the lid and install the element.

The replacemnet screw is thicker than the original one, so you might want to drill out the hole very slightly. I did not but the resistance was high on getting the screw fully seated.

Works great