111P02 Briggs and Stratton Engine - Overview

Models starting with 111P02

Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Pin-piston/std – Part Number: 298909
Pin-piston/std
PartSelect #: PS8942667
Manufacturer #: 298909
$15.95
  Special Order
Key-flywheel – Part Number: 222698S
Key-flywheel
PartSelect #: PS8925657
Manufacturer #: 222698S
This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Plier...
$5.95
  In Stock
Kit-needle/seat – Part Number: 398188
Kit-needle/seat
PartSelect #: PS8963322
Manufacturer #: 398188
Genuine manufacturer approved carburetor needle valve for lawn and garden equipment engines. This item includes the seat. The needle valve opens and closes to control the flow of fuel into the carbure...
$11.95
  In Stock
Seal-oil – Part Number: 399781S
Seal-oil
PartSelect #: PS8960670
Manufacturer #: 399781S
This is an authentic replacement part manufactured for use with small engines. Seals can deteriorate overtime, and it is recommended to replace worn seals when servicing an engine. This seal is the lo...
$13.95
  Special Order
Washer-sealing – Part Number: 271716
Washer-sealing
PartSelect #: PS8940580
Manufacturer #: 271716
This authentic OEM sealing washer is designed for your lawn equipment to create a tight seal within the carburetor body, preventing fuel or air leaks. If you notice any signs of leaks, such as drippin...
$6.95
  Special Order
Plug-Spark Ems – Part Number: 692720
Plug-Spark Ems
PartSelect #: PS9066631
Manufacturer #: 692720
$12.95
  Special Order
Engine Spark Plug Terminal – Part Number: 493880S
Engine Spark Plug Terminal
PartSelect #: PS8988266
Manufacturer #: 493880S
This spark plug terminal is supplied directly from the original equipment manufacturer. The metal terminal is designed to fasten the spark plug to the engine lead wire. This component is sold individu...
$5.95
  Special Order
Retainer-Gov Shaft – Part Number: 690340
Retainer-Gov Shaft
PartSelect #: PS9062930
Manufacturer #: 690340
$7.95
  Special Order
Stud – Part Number: 793479
Stud
PartSelect #: PS9137005
Manufacturer #: 793479
$9.95
  Special Order
Stud – Part Number: 797002
Stud
PartSelect #: PS9137994
Manufacturer #: 797002
$11.95
  Special Order
Adjuster-Rocker Arm – Part Number: 796631
Adjuster-Rocker Arm
PartSelect #: PS9138586
Manufacturer #: 796631
$24.95
  Special Order
Filter-air Cleaner Ca – Part Number: 795066
Filter-air Cleaner Ca
PartSelect #: PS9137508
Manufacturer #: 795066
This high quality replacement air cleaner cartridge is specially designed for use with Briggs and Stratton engines. It is an authentic OEM sourced item, not an aftermarket equivalent. It is utilized t...
$23.95
  In Stock

Common Symptoms of models starting with 111P02

[Viewing 1 of 1]
Will Not Start
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Bought Troy Built pressure Washer at garage Sale for $30.00 leaked fuel
I have a solid understanding of small engines. This pressure washer was used twice in 2013, when purchased. Sat in a garage for a couple of years with gas in tank and carburetor. Owner was moving and after 7 years of moving it around he sold it at a garage sale.
I took it home and took off gas tank and thoroughly cleaned it. Then went through the carburetor and let soak in cleaner. Cleaned up the spark plug, tested and has good spark. reinstalled carburetor but would not start. I knew I had gas issues. I ordered a carburetor kit and replace the needle valve and seals. Still would not start. Ordered a new carburetor and spark plug. Installed both. Two pulls and it runs like new. Advice: don't try to clean out old carburetor, just buy a new one and install.
Parts Used:
Kit-carb Overhaul
  • Laird from North Las Vegas, NV
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The exhaust system just fell off the motor
I ordered the parts as there were only three screws and two bolts that needed to come out and then thenew ones go back in. Everything went just as planned...….well except the two bolts that where included by Briggs and Stratton appear to be 1/8-1/4" too short and now both of the threaded holes in the engine are now stripped and the quick easy repair is now a bust and not repairable by me.

This has nothing to do with PartSelect.com as they just shipped the Briggs and Stratton part box.
Parts Used:
Muffler
  • Darrel from SARASOTA, FL
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Screw in new dipstick, check oil level
Very well
Parts Used:
Dipstick
  • Kim from KENNER, LA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
5 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!