111P02 (0016-F1) Briggs and Stratton Engine - Overview
Sections of the 111P02
[Viewing 1 of 1]Keep searches simple, eg. "belt" or "pump".
Seal-oil
PartSelect #: PS8960670
Manufacturer #: 399781S
This is an authentic replacement part manufactured for use with small engines. Seals can deteriorate overtime, and it is recommended to replace worn seals when servicing an engine. This seal is the lo...
$13.95
Special Order
Key-flywheel
PartSelect #: PS8925657
Manufacturer #: 222698S
This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Plier...
$5.95
In Stock
Engine Spark Plug Terminal
PartSelect #: PS8988266
Manufacturer #: 493880S
This spark plug terminal is supplied directly from the original equipment manufacturer. The metal terminal is designed to fasten the spark plug to the engine lead wire. This component is sold individu...
$5.95
Special Order
Filter-air Cleaner Ca
PartSelect #: PS9137508
Manufacturer #: 795066
This high quality replacement air cleaner cartridge is specially designed for use with Briggs and Stratton engines. It is an authentic OEM sourced item, not an aftermarket equivalent. It is utilized t...
$23.95
In Stock
Gasket-cylinder Head
PartSelect #: PS9152268
Manufacturer #: 796475
This is an authentic replacement part manufactured for use with small engines. The cylinder head gasket forms a seal between the cylinder head, and cylinder. It is recommended to replace gaskets when ...
$20.95
Special Order
Retainer-valve
PartSelect #: PS9074718
Manufacturer #: 692194
This is an authentic replacement part manufactured for use with Briggs & Stratton small engines. The special retainer is commonly used as spacing between the head of the valve and the valve spring. Th...
$10.95
Special Order
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Bought Troy Built pressure Washer at garage Sale for $30.00 leaked fuel
I have a solid understanding of small engines. This pressure washer was used twice in 2013, when purchased. Sat in a garage for a couple of years with gas in tank and carburetor. Owner was moving and after 7 years of moving it around he sold it at a garage sale.
I took it home and took off gas tank and thoroughly cleaned it. Then went through the carburetor and let soak in cleaner. Cleaned up the spark plug, tested and has good spark. reinstalled carburetor but would not start. I knew I had gas issues. I ordered a carburetor kit and replace the needle valve and seals. Still would not start. Ordered a new carburetor and spark plug. Installed both. Two pulls and it runs like new. Advice: don't try to clean out old carburetor, just buy a new one and install.
I took it home and took off gas tank and thoroughly cleaned it. Then went through the carburetor and let soak in cleaner. Cleaned up the spark plug, tested and has good spark. reinstalled carburetor but would not start. I knew I had gas issues. I ordered a carburetor kit and replace the needle valve and seals. Still would not start. Ordered a new carburetor and spark plug. Installed both. Two pulls and it runs like new. Advice: don't try to clean out old carburetor, just buy a new one and install.
Parts Used:
-
Laird from North Las Vegas, NV
-
Difficulty Level:Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The exhaust system just fell off the motor
I ordered the parts as there were only three screws and two bolts that needed to come out and then thenew ones go back in. Everything went just as planned...….well except the two bolts that where included by Briggs and Stratton appear to be 1/8-1/4" too short and now both of the threaded holes in the engine are now stripped and the quick easy repair is now a bust and not repairable by me.
This has nothing to do with PartSelect.com as they just shipped the Briggs and Stratton part box.
This has nothing to do with PartSelect.com as they just shipped the Briggs and Stratton part box.
Parts Used:
-
Darrel from SARASOTA, FL
-
Difficulty Level:Very Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Screw in new dipstick, check oil level
-
Kim from KENNER, LA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
5 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!