Models > 110C61112010 > Instructions

110C61112010 Kenmore Dryer - Instructions

All Instructions for the 110C61112010
16 - 30 of 62
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer would stop after a very short time when cold, wouldn't keep running at all when hot
At first I was advised to replace the temperature overload sensors, which I did but didn't fix the problem. After adding the additional information that the dryer would run to full cycle as long as the Start switch was held in I was advised to replace the Start switch.

It wasn't obvious from the wiring diagram, but if you remove the Start switch and look at the side it shows it contains a solenoid holding circuit that keeps the switch in the "on" mode as long as there is a feedback signal from the temperature overload switches. So if the dryer will run to completion if the switch is held in, replace the Start switch. If it still stops mid-cycle, replace the temperature overload switches.

The replacement videos were spot on as far as clear and easy to follow instructions for the repair, and all ordered parts were delivered very quickly.

Thanks for your help PartsSelect!
Parts Used:
Push-to-Start Switch
  • Paul from ANTIOCH, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer was not heating and sometimes would not start at all
Unplugged dryer
Removed back
Removed knob and screw from front and 2 screws from the timer in the back unplugged one wire at a time and replaced one at a time.
Dryer working great.
Parts Used:
Timer
  • Cindy from GATES, TN
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Timer stopped working
Used your video, went very easy
Parts Used:
Timer
  • Gordon from PALATKA, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Push button wouldn't work
Still wouldn't work! Push switch returned to you but have not received a refund yet. The repair was very easy. Tracking # 1Z 2R5 3A2 03 0025 9453 for returned switch.

















3
Parts Used:
Push-to-Start Switch
  • Carolyn from STIGLER, OK
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken handle
1) removed the old broken filter
2) deposited it in nearby wastebasket (with lint attached)
3) used scissors (see above) to remove plastic cover from new lint filter
4) inserted new lint filter
5) marveled at my handiwork!
Parts Used:
LINT SCREEN ASSY, WOD
  • John from New Bedford, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lint Filter wore out had to be replace
Changed out the lint filter
Parts Used:
LINT SCREEN ASSY, WOD
  • Don from Dayton, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lint Filter wore out.
It required no tools, just take out the old torn filter and slip in the new one. I should have ordered it a year ago, with the ease of the website and the delivery via Fed Ex. super easy.
Parts Used:
LINT SCREEN ASSY, WOD
  • Claude from Austin, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
DRYER RUNS BUT DOES NOT GET HOT
OPENED REAR OF DRYER TOP PANEL, TESTED FOR CONTINUITY ON TIMER, ALL TEMP SENSORS AND HEATER COIL WITH MULTI-MEETER AS DESCRIBED IN ONLINE YOUTUBE VIDEO FOR WHIRLPOOL DRYERS. TIMER TESTED BAD AND REPLACED TIMER. EASY TO UNSCREW AND UNPLUG.
Parts Used:
Timer
  • JOE from AQUEBOGUE, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
TIMER WENT BAD AND KNOB BROKE OFF
I REMOVED THE OLD TIMER AND INSTALLED THE NEW ONE. ALL I NEEDED WAS A 3/8 SOCKET AND IT TOOK LESS THAN 15 MINUTES. I USUALLY CANNOT FIX ANYTHING AND THIS WAS VERY SIMPLE AND THE VIDEO SHOWED ME EXACTLY WHAT TO DO. THE PART IS WORKING OK SO FAR.
Parts Used:
Timer
  • Andrew from MANAHAWKIN, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed a new lint filter
Took the old one out, replaced it with new one.
Parts Used:
LINT SCREEN ASSY, WOD
  • Evelyn from JACKSONVILLE, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No problem
My son did the repair and said it was so easy!
Parts Used:
Timer
  • Yvette Joan from DUSON, LA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lint filter cracked
Removed old filter, replaced with new.
Parts Used:
LINT SCREEN ASSY, WOD
  • Cynthia from POLAND, ME
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lint would no go throw
Received the new lint removal from the box and install it easily
Parts Used:
LINT SCREEN ASSY, WOD
  • Jean M from CHESAPEAKE, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the handle had broken on the lint filter so i had fashioned paper clips into the holes to get the filter out
after i got the replacement filter, it fit perfectly. the filter is white & my dryer is beige but i don't care...i'm just happy i have a good lint filter again, for my at least 30 year old dryer....thanks part select!
Parts Used:
LINT SCREEN ASSY, WOD
  • Stacey from Corinth, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Easy
Took the back off with nut driver and took out defective timer. Then put in new one.
Parts Used:
Timer
  • Patricia from PARADISE, MT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 110C61112010
16 - 30 of 62