11065212610 Kenmore Dryer - Instructions

My husband removed the old (2) thermostats..then installed the new ones...he said the only thing he needed was his battery run screwdriver, and it was really needed!
we are happy with the ordering, delivery, and the ease of replacement of our new parts. Thanks.

Took the back off with a cordless drill with an apex holder. I unplugged the old wires from the old heating element and plugged them into the new heating element. Put the back back on after testing it to make sure it worked and that was it. Since this element was in a housing it was really simple to reinstall the new one.

After the new filter arrived, I took the old filter out, put the newe one in. No tools, no difficulty at all. Actually, the really difficult part of this entire episode was finding the model number on the dryer. It was on the underside of the door.

Very Very Easy all you need is a 1/4 inch nutdriver. 1st remove the screws from the back of the dryer. 2nd you will see a shaft like duct work. remove the 2 screws from this shaftway, lift out the old heating element and replace with the new element. Part select was right on target and fast. 2 days to recieve my order. I expected to have to buy a new appliance. Partselect made it possible to fix it like new for around $80.00

the job would have gone faster if the right parts had been sent in the first place. I would have never paid for two day shipping. In the repair, I removed the rear panel, clipped the plastic triangle holding the bearing, installed the new bearing and new clip.

I watched the installation video on both parts before I purchased them and it was a piece-of-cake after that.

Lint screen on my 30-year dryer was torn. Ordered the new screen here with just the part number, fits well. Very helpful website.

Unplugged dryer. Removed dial. Removed old timer (3 screws) and left wires attached. Installed new timer. Disconnected wires from old timer to connect on new timer. Plugged in dryer......everything worked again.

Removed top and front of dryer then drum and followed the instructions in the package. It was a real simple procedure. I did additional cleaning while the dryer was disassembled.

I watched the video on how to diagnose problem and then how to repair . Videos were very helpful. Also the parts were ordered on line and arrived in 2 days. Parts at a local appliance parts store were twice the cost of what I paid for the parts from PartSelect.

Once I unpluged the dryer and then removed the back cover, I located the heating unit and then removed the thermostat. Once that was done, I installed the new thermostat and connected the wires. I tested the dryer to make sure that it would heat. Then I replaced the back cover.

checked all the thermostats and the heating element all good had continuity checked the red wire from the timer to the element and it was not sending 120v to the element consistently ordered the timer and replaced in 15 minutes had my dryer heating and drying clothes
parts select had all the wiring diagrams on my model and a how to do video made it easy peasy

I didn't think I could find a replacement part because the dryer was so old (it has fake wood paneling!) and I was already considering the cost of a new dryer. I searched online and found this site. I crossed my fingers and placed my order. When it came, I removed what was left of the old lint remover and put in the new one. It was a perfect match. The colors were a bit off but who cares. PartSelect saved me from having to purchase a new dryer. Yay!

Unplug dryer,remove top rear panel.remove wires from old timer and reconnect to the new one,replace panel.

At first I was advised to replace the temperature overload sensors, which I did but didn't fix the problem. After adding the additional information that the dryer would run to full cycle as long as the Start switch was held in I was advised to replace the Start switch.

It wasn't obvious from the wiring diagram, but if you remove the Start switch and look at the side it shows it contains a solenoid holding circuit that keeps the switch in the "on" mode as long as there is a feedback signal from the temperature overload switches. So if the dryer will run to completion if the switch is held in, replace the Start switch. If it still stops mid-cycle, replace the temperature overload switches.

The replacement videos were spot on as far as clear and easy to follow instructions for the repair, and all ordered parts were delivered very quickly.

Thanks for your help PartsSelect!