11065212610 Kenmore Dryer - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer Drum Support Roller – Part Number: WPW10314173
$28.21
In Stock
Dryer Drum Support Roller
★★★★★
★★★★★
(15)
Part #WPW10314173
This genuine OEM dryer drum support roller is designed to hold the drum in place while allowing it to rotate smoothly and quietly during operation. Built for durability and reliable performance, it helps reduce noise and ensures consistent tumbling. Ideal for replacing worn or damaged rollers, it resolves issues such as squeaking, rumbling, or poor drum movement, helping restore efficient and dependable dryer operation.
Heating Element - 240V 5400W – Part Number: 279838
$79.60
In Stock
Heating Element - 240V 5400W
★★★★★
★★★★★
(83)
Part #279838
This 240V/5400W heating element is strung with a coiled wire made of a nickel and a chrome alloy. This wire receives, but resists, a controlled electric current, causing the wire to heat up. The heat produced is used to dry the clothes in your dryer. If the dryer has no heat, takes too long to dry, or the heating element burns out, the heating element will need to be replaced since it cannot be repaired. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting your repair.
Dryer Cycling Thermostat – Part Number: WP3387134
$35.80
In Stock
Dryer Cycling Thermostat
★★★★★
★★★★★
(18)
Part #WP3387134
Cycling thermostats continually cycle the heating element off and on to maintain a constant inner temperature. This particular cycling thermostat has a limit of 155 degrees Fahrenheit and a differential of 25 degrees. Meaning that the heating element will cut out at 155 degrees and cycle back on once the internal temperature drops by 25 degrees.
Roller Support Tri-Ring – Part Number: WPW10512946
$18.70
In Stock
Roller Support Tri-Ring
★★★★★
★★★★★
(4)
Part #WPW10512946
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pulley shaft, or on the rear drum roller shaft. In either case, you will need to remove the front panel of the dryer and the drum to access the part for repair. Once you have accessed the damaged tri ring, you will simply need to slip it off and replace it with the new one. This part is sold individually. Be sure to disconnect the power source from the dryer before you begin this repair.
Dryer High Limit Thermostat – Part Number: WP3977767
$29.65
In Stock
Dryer High Limit Thermostat
★★★★★
★★★★★
(7)
Part #WP3977767
This high-limit thermostat with Terminal Extension Arm acts as as safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches 221 degrees Fahrenheit, this piece will shut down power to the heating element until it drops by 80 degrees Fahrenheit.
Rear Drum Felt Seal – Part Number: W10612022
$60.69
In Stock
Rear Drum Felt Seal
★★★★★
★★★★★
(27)
Part #W10612022
This seals Includes adhesive. This part helps seal the drum to prevent hot air from escaping.
Refrigerator Light Bulb 10w – Part Number: WP22002263
$28.08
In Stock
Refrigerator Light Bulb 10w
★★★★★
★★★★★
(10)
Part #WP22002263
Brighten up your appliance with this easy-to-install 10-watt light bulb, perfect for dryers and refrigerators. It gives off a clear, steady light so you can easily see inside when the door is open. Whether you're replacing a bulb in your Whirlpool or another compatible brand, this one fits right in. Just twist it into place—no tools needed. For safety, make sure your appliance is turned off before swapping the bulb.
Heating Element Connection Wire Kit – Part Number: 279457
$13.97
In Stock
Heating Element Connection Wire Kit
★★★★★
★★★★★
(4)
Part #279457
This kit is used for electric clothes dryers, and it comes with a yellow wire nut.
Timer – Part Number: WPW10185982
$176.33
In Stock
Timer
★★★★★
★★★★★
(39)
Part #WPW10185982
This dryer timer is used to control the unit's cycles by regulating the length of time that power is directed to each setting.
Dryer Lint Trap Housing Seal – Part Number: WP339956
$15.95
In Stock
Dryer Lint Trap Housing Seal
★★★★★
★★★★★
(4)
Part #WP339956
This seal comes with the adhesive backing.
Two-Piece Split Ring Bearing – Part Number: 279441
$80.71
In Stock
Two-Piece Split Ring Bearing
★★★★★
★★★★★
(9)
Part #279441
This is a replacement bearing ring kit for your dryer. The bearing rings are found on the top and bottom lips of the dryer drum. If your dryer is unusually noisy, or the drum will not turn during operation, or if there are marks left on your clothes after a cycle, you may need to replace the bearing ring kit. The kit comes with 2 bearings, one for the top and one for the bottom of the dryer drum. Remove the front panel of your dryer to access the dryer drum for this repair. At this point you can use a pair of needle nose pliers to release the old bearing rings from the drum. Snap the new bearing rings on, and reassemble the dryer to complete your repair.
Dryer Seal – Part Number: W11415783
$24.93
In Stock
Dryer Seal
★★★★★
★★★★★
(1)
Part #W11415783
This seal comes with the adhesive backing.

Common Symptoms of the 11065212610

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer motor runs, but no heat
2308 of 2510 people found this instruction helpful.
  • Gadi from Irvine, CA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
To reach the heating element you only need to open the back cover of the dryer (about 8 nut-head screws). Remember to disconnect the power.

To remove the heating element there are two small nut-head screws. Remove the two electric wires. Then you can pull the heating element away.

You can check the heating element wi th an ohm-meter or visually inspect it to see if the heating element spiral wire is broken.

Don't hurry to dispose the old element. My model includes a small electric safety part. You'll need to transfer it to the new heating element (that comes without it)..

Good luck.
Was this helpful?
Thank you for voting!
Dryer would run with no heat.
731 of 766 people found this instruction helpful.
  • Remie from Mahopac, NY
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
The repair was easy. the most time consuming part was vacuuming the dust from the back of the Dryer, The repair required removing screw from the back panel of the dryer. Then removing screws from the heating element and unplugging the wires. The only moderately diffculy part was swapping the sensor form the old element.
Was this helpful?
Thank you for voting!
No heat for dryer
497 of 521 people found this instruction helpful.
  • Leslie from Dallas, TX
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
Moved dryer from wall,disconnected power. Unscrewed the 12+ sheet metal screws holding on the back cover. Located heating element, remover it's two sheet metal screws and pulled down on the element to remove. Disconnected the two electrical leads from element and went to the top of Dryer. Do not remiember if told to remove the temptur e kill button was easy to see that it was needed on new element. Moved high tempeture senson to new element. Reversed steps to install new element. Replaced back cover, pluged in and powered up. Works like a champ. Thanks for the price on the part and the video which started me on the right track. I'll be back !!
Was this helpful?
Thank you for voting!