All Installation Instructions for Kenmore Refrigerator 10663996200

The freezer worked fine but the refrigerator wasn’t getting cold.

I removed the flat panel inside freezer & fan blades not turning. I removed 2 1/4” screws, unplugged wires took fan motor out & put that fan blade on new fan motor. Plugged wires into new motor replaced 2 bolts, reinstalled flat panel plugged refrigerator in & reset temperature controls. The next day checked temperature and was all done.

Parts Used:

Refrigerator Evaporator Fan Motor

Ray from Wiggins, MS
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Crisper drawer rail broken at one end

The rail just snapped into place with a light pressure. I worried it would require manipulation or heavy pressure and I would break the end while installing it.

Parts Used:

Refrigerator Crisper Drawer Rail

MARTY from GREAT FALLS, MT
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Condenser motor was making noise.

Removed the cardboard baking on back. Unplugged the fan. Used 1/4 socket and removed the 3 nuts. Removed the fan. It is tight quarters. Take your time and the job will go fast.

Parts Used:

Condenser Fan Motor Kit

Joe from Spring Hill, TN
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Socket set

4 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Drain clogging causing water to leak bottom of fridge

After watching videos how to replace went very easy.removed ice maker cut wires replaced switch put back together now working ok so far.

Parts Used:

Refrigerator Bimetal Defrost Thermostat

Ted C from DSRT HOT SPGS, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Faulty light socket

Followed the video instructions.

Parts Used:

Light Socket Kit

Larry from HOUSTON, TX
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

The door shelf brace was missing.

I snapped the two end caps into the shelf rail and pushed it into place on the bottom of the inside door.Tolls were not needed as it was a perfect fit.

Parts Used:

Door Retainer bar - White

Refrigerator End Cap Trim Piece

Gary from COLUMBUS, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Freezer Bulb failed

Unscrewed bulb from sock .
Replaced with new one . Now working

Parts Used:

BULB-LIGHT

Kevin from SWANVILLE, ME
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Door light switch disintegrated

Very simple fix, remove 3 screws, two connectors to the old switch

Parts Used:

Refrigerator Door Switch

Thomas from Roseville, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Replacing the bulb in the freezer side

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Parts Used:

Light Bulb - 40W

Yafa (and David) from Bothell, WA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

5 of 11 people found this instruction helpful.

Was this instruction helpful to you?

fridge door switch did not work

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

Parts Used:

Refrigerator Door Switch

stu from richmond, VA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

replaced motor and fan

I have a grandson that works for Pantex. He replaced the fan and motor in less than ten minutes using only the nutdriver tool. My cost compared to local supplier and labor was about 75% less.

Parts Used:

Condenser Fan Motor Kit

Rex from Amarillo, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Light didnt go on

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

Parts Used:

Refrigerator Door Switch

dorotea from staten island, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Clear Dairy Door Broken

It was simply placing the clear $60.00 door in place. It was a very simple fix, but expensive!

Parts Used:

Refrigerator Door Compartment

Robert from Hemet, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Broke light switch while cleaning

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

Parts Used:

Refrigerator Door Switch