X-Large Burner Head with Electrode 74007736

Unscrewed burner head and replaced with new burnerhead and electrode. Just like new. Parts cost 128.00 including shipping. Very simple repair. Saved 200.00 in labor. Parts came within 36 hours. Super Fast.

I first tried to remove the torx screws only to have them break off..soooo as with most home repairs it grew into a bigger task. 1) unhooked the gas line and unplugged the unit 2) place the unit upside down on workbench 3) used a socket set to remove the hex screws that held the top on 4)removed all the other burners and disconnected electrical wire connected to the igniters. 5) Removed the top 6) uses pliers to remove the screw parts left in the burner base (wd-40 and lock wrench)..Replaced the old gaskets 7) put the top back on and screwed the top back on (make sure you pull the igniter wires through the top before securing it) 8) Reseat and screw in the burners using a torx bit

Installing the 2 new burner assemblies worked great with the new screws. New screws however, did not work with the old burner assemblies that have rusted screws I wanted to replace. New burner assemblies are slightly taller that the old ones.

Disassembly: Removed 2 screws with nutdriver. Pulled off electrode connection. Screws were rusted and needed replacement.

Assembly: Slipped on electrode attachment. Went to local hardware store and bought 5/8" 8/18 pan head screws. Used screwdriver to screw down burner head. The 3/8" inch screws on the tech sheet do not work. Too short and flange is too wide to fit in opening in burner head.

The ceramic on the electrode broke due to water over boiling the week of Thanksgiving. When i tried to loosen the screw to replace the electrode it broke off inside the threads. Ordered whole new unit overnight. Back in business in five minutes. Thanksgiving was back on!! Thanks!

This is the 3rd burner head that was replaced . everyone had the screws break off , & had to be drilled out & re tapped .I would not purchase the replacement screws @$4.00 each . They were just plain sheet metal screws that were steel . Better going to a home center & purchasing brass or stainless machine screws at a 1/4 of the cost .If you are not familiar with drilling out broken screws ,then this is not the repair for you .

Wanted to deep clean the range, but popped the worn screw heads on both the burner mounts and igniters embedded in the chassis. The way the range is designed, the bolts extend through the glass top and into the burner orifice. The bolts were unable to be extracted so replacement was the only option outside of a small third party machine shop. The double burner is discontinued and impossible to find, will replace this "High-End" POS when we remodel.

Removed Burner Heads
Disconnected igniter Leads
Extended range to remove glass top
Removed glass top mounting screws
CAREFULLY Removed Glass Top (REPLACEMENT = $800 Min)
Removed affected burner orifices
Tracked down parts list and maintenance manuals
Tracked down similar issue:
https://www.youtube.com/watch?v=YfCLJ1rXK6w&t=114s
Replacement bolts : #8 24 X 0.5" Sheet Metal Screws
Ordered Replacement parts and installed in reverse

Unscrewed burner assembly and removed wire. Unable to remove electrode screw. Striped head of screw. Tried penetrating oil but no luck. Tried to drill and use easy out bit but ruined burner assembly and had to order new burner assembly. When assembly came it had electrode in place but website does not show electrode with assembly except on one burner. With mail and all it took about a week to fix 2 burners. Returned unused electrode for credit. Overall, cheaper then a service call by far.

Replaced burner assembly.

Removed the two fastening screws with a small square head screwdriver,lifted the burner head disconnected wire from damaged electrode. To install just reversed the steps,total time less than ten minutes.