This is the burner head and electrode for your gas range. If your gas igniter glows but will not light, or if the element will not start or heat entirely, you may need to replace the burner head. This...
$103.41
In Stock
Order within the next 49 mins and your part ships today!
This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
$299.94
In Stock
Order within the next 49 mins and your part ships today!
Questions And Answers for JGC8536BDB11
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ritva
February 21, 2022
When I turn the burner on, it ignites but it's clicking.
The technician suggests to install Spark Module WP8286828.
He already installed a new switch WP74007774, it didn't solve the problem.
Please, help me!
Thank you.
For model number JGC8536BDB11
Hi Ritva,
Thank you for your question. If your burner is clicking when it is on, the burner cap may be out of alignment. You will need to turn the burner off and allow it to cool before inspecting it. If you have just recently cleaned the stovetop or if there have been any spills, moisture may have gotten in the burner and you will need to let it dry. If you notice any moisture, take a cloth and wipe it up. If there is any food debris on the burner, you will need to use a metal pin to clean it. If you have any questions, please let us know. We are open 7 days a week. We look forward to hearing from you!
1 person found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
As others reported, there are 2 torx screws that need to be removed so that the burner element can be removed. One came out with a little effort, the other one did not as it was corroded. After breaking a torx bit, a second torx bit succeeded in breaking off the screw head. This then required a drill to drill out the broken shaft and then rethreading the screw hole. On to the ignitor replacement. The tiny screw holding the ignitor was corroded and would not come out. It too had to be drllled out and rethreaded. It was a 1/3" #4 screw with fine threads. Had to get it an appliance repair store as the local hardware places don't carry fine threaded screws. Finally got it all put back together after a week. My advice before ordering an ignitor is make sure you can take the current burner off the cooktop first to do the repair in the first place. BTW, the ignitor I ordered came quickly and was the correct part!
Firts I removed the 2 screws that held the burber in place. Then I lifted the burner up & disconnected the wire that connected to the ignitor. Then I removed the one screw that held the ignitor to the burner. I then reversed these steps, replacing the cracked ignitor with the new one, replaced the screw holding it to the burner, then reconnected wire, returned the burner to the stove and replaced the two screws that held it. All Done!
- Removed the cover. - Removed te two Torx screws. - Pulled the burner a couple of inches to be able to disconnect the wire. - Spent a lot of time removing the small Philips screw holding the ignitor. Ended up breaking the ignitor with pliers to be able to put WD40 under the screw's head. - Treated all screws with a high temperature copper paste to prevent oxidation. Installed the new ignitor with the new screw. - Reconnected the wire. - Installed the two Torx screws. - Voila, it works.