ZIR301NPNAII General Electric Refrigerator - Instructions

After turning the water off, I removed the silver covering located on the left side bottom. The valve was connected to the frame on the left side. I removed the defective valve and replaced it with the new one. Everything was color coded and the hoses were different sizes, making it impossible to screw up. It was over so fast I thought I made a mistake.

I thought it must be the water valve leaking by so I ordered one and put it on myself which was a very easy job. It fixed my problem and everything works fine now. First I unplugged the refrigerator shut off water line block shutoff valve. Then I removed the back plate on refiigerator. Then I removed the water line from the water valve. After that I unplugged the two wiring harnesses. Then I removed the two plastic water lines from water valve. then I inbolted the water valve from refrigerator. Then I got new valve, plugged both water lines into it, plugged both wiring harnesses back into it, hooked main water line back up then turned water back on.

I followed the video for my model refrigerator on parts select. My hint: when returning the back panel of the freezer, it's slightly adjustable left and right to avoid grazing the fan.

WE (WIFE) took out the old parts an replaced with new one ..Be careful to get the placement of the Grommet or they "POP" out on you. fast ship on the parts too.

First time the water hose in the door was frozen. Thawed hose and started water flow. About 2 week later water stopped once again. Did a little trouble shooting and determined the valve stopped working. Ordered a unit, installed in a very shor time and all is good so far.

I changed the filter first as this has happened before when the filter got too old. Still did not work, so ordered the double outlet water valve as the ice dispenser was working. The part was easy to install with the video directions. However, water still did not dispense. Felt the water coil behind the crisper in the refrigerator and it seemed kind of hard. I wondered if it was frozen. Took a hair dryer to it for about 45 seconds and then tried the water again. Voila' This time it worked. Apparently it WAS frozen. I may have not needed to change the filter or water valve, but everything is working fine so I will leave well enough alone.

First, turn off main water valve. Then, at the rear of refrigerator remove the rear panel exposing the water valve assembly. Cautiously, proceed by disconnecting the water hose and electrical connections. To complete the task, just worked in the reverse steps to exchange the faulty equipment.

Find a video on youtube. Remove 6 screws. Pull the Styrofoam part up before removing the panel. Unplug and Remove the fan assembly.
You will need a NUT DRIVER to take the bracket off the backing plate.
I ordered the red grommet and the red bumper. You need TWO of the red grommets if that is the problem. My freezer was about 8 years old, and the grommets were worn and compressed, the bumper was not. Replacing these parts DID NOT FIX the problem. I needed a new motor.
I probably disassembled and reassembled this stuff about 7 times before I got all the parts and tools. Each time I had to unload the freezer.

1 unplug fridge
2 turn off supply line for ice maker
2 remove lower back panel of fridge
3 disconnect in and out line from valve
4 remove valve (one screw.)
5 disconnect power line to valve.
reverse to reinstall. Very easy.

This valve is a cheap, poor design. This is the second one in 5 years. I replaced the first one because the line in the freezer would "drip" creating an ice dam so the ice maker wouldn't work. This time, the water dispenser on the front of the fridge has been dripping for months - finally the valve just dissolved and was spraying water all over the floor. It ran down into the basement. Keep a eye out if you have a GE fridge.

I followed your video and completely dismantled the refrigerator evaporator motor, fan, brackets, and grommet, I completely cleaned the refrigerator including the cooling coils. I then ordered the evaporator motor ,fan, grommets, lid bumper, and brackets. The order would take a week to arrive. In the meantime I cleaned and reassembled all the old parts, waiting for the new ones to come. Guess what! The refrigerator was quiet as a mouse. I really did not need the new parts, but I kept them anyway just for good luck. Not bad for a refrigerator that's twenty four years old.

1. remove back shield of fridge.
2. unscrew old valve.
3. remove electrical connections.
4. remove white inserts on new valve.
5. cut feed hoses next to old valve.
6. place white inserts on hoses.
7 insert hoses into recepticals on new valve.
8 shut off water supply to fridge.
9. remove water suply line from old valve.
10. attach water supply line to new valve.
11. connect electrical connections.
12. bolt valve back on to fridge
13. turn on water supply to fridge
14. test both ice maker and water dispensor
15. replace back shield to fridge

Remove ice maker and all of it's accessories in order to remove the panel covering the fan. Don't drop the screws!
Unscrew the lower fan bracket. You will see the lower red rubber grommet. Hold fan motor with one hand and push the fan off the shaft and into the compartment above. Then remove the round retainer thing below it by holding it and pulling down on the motor assembly. Install new grommet on upper part. and put it all together.
REMEMBER where the fan is on the shaft. It has about one inch of shaft placement. I put mine so that most of it was above the hole that the fan goes into and about 20 percent showing below the sheet metal.
Also check to see if your fan is damaged. Mine was not.
This refrigerator has been awesome! I have had many issues but have been able to fix all of them for the last 15 years!

Removed ice bucket, and unplugged ice maker. Removed light cover. Removed ice maker. Pulled fan blades straight up and removed. Pushed new blades on to motor shaft. Fairly easy .

Unplugged the freezer. Then I gained access to the fan: remove the top freezer rack, remove the ice tray, remove the air flow manifold(needed to unscrew some screws), remove the manifold over the fan and cooling element. I unscrewed the fan mounting bracket. The fan motor's wires are plumbed through some plastic that i would have had to remove, so I decided instead to cut the wires and splice in the new fan motor. Then I put everything back together - the new motor works fine and doesn't make the whining noise.

Diagnosis: I removed the nuts holding on the panel at the back of the refrigerator and saw water leaking from the water valve.

Repair: I guided my 10 year old daughter through the actual replacement.

Using a nut driver, unscrew the single nut holding the value to the frame of the refigerator.

Push up the rings around each water tube to release the tubes from the value. Using a wrench, unscrew the supply line.

Put dab of plumbers teflon on the threads.

Reverse all the above:
Screw in supply line, tighten with wrench.
Push water lines for icemaker and chilled water into value assembly.
Position valve and screw in het nut that attaches it to the frame.
Replace rear cover plate and screw in the hex nuts.