YAED4475TQ1 Admiral Dryer - Instructions

I noticed my dryer was heating, but not tumbling. I"m a 53 year old single female, and my dryer I bought used 3 years ago. I had no clue what the problem was. I texted my brother and said, "it heats but doesn't tumble - is it shot?" He texted back "probably the drive belt - pop the top and see." So I popped the top, and sure enough, the belt was broken. So I googled "diy + dryer + drive belt" and watched a You Tube video. I then drove all over town looking for a belt, and the only place that carried it had closed at noon (saturday). So I googled " appliance parts + dryer and came to this site, ordered the part and it was delivered in two days.
I borrowed a nut driver from my brother, removed the front of the dryer, used a plastic cup to prop up the drum. I put the belt on the drum, being sure to place the ribbed side down, looped through the pulley and onto the motor, removed the cup, put the front back on, dropped the top, replaced the lint trap and the two screws holding that in place, turned the dryer on and voila! All done.

remove the front panel, belt [notice the way the belt is fasten] remove the tub, support bracket to the drum roller, and slide the new drum roller on and place the tre ring in the slot. then re-install everything in reverse

I received the part I ordered immediately and the included instructions made installation a snap. Thank you for your help. I would not hesitate to order from your company again.

Followed the video instructions that I was directed to through this site. The time it took me includes the time I used to vacuum out the back of the dryer and remove lint build up. The repair was very easy since the video provides all the information you need in an easy to follow format. I used my cell phone and paused when I needed to. Great site, great access to parts and great service. My parts were delivered in 2 days!

removed old gasket took door off 4 screws. cleaned seal area applied glue put on gasket easy

Unplugged unit and removed top and front of dryer. Removed drum and belt. noting how belt ran through the belt tension-er. Removed old felt seal from rear of drum. Replaced broken baffle, replaced rear seal. reinstalled belt. Put unit back together and test ran.

Asking my question on you tube they show me problems and parts to need replace and how do installation.

Used the maintenance kit....followed the movie tutorial. I also used an empty gallon plastic container to support the front of the drum while stretching the belt over the motor pulley. For the rear drum rollers, before sliding them on the shaft, I put a light grease film on the shaft. After the repair, the dryer runs quieter.

Moved top control panel and pulled cabnet back changing switch,then reassembled,very easy,don’t forget to un plug

First only replaced the high temp cut off switch which allowed the element to heat. However, after one heat cycle the switch would not reset. Then changed the thermostat (included in the kit). After tapping the cut off switch lightly to manually reset it, the dryer ran perfectly. Moral of the story: always change all parts included with a repair kit!

Take the door off of the dryer. Lay it on a towel. Remove old gasket. Clean the channel the door gasket fits into with glue remover. Squeeze high temperature glue into the channel, let the glue set up. Put the new gasket into the channel, tape it down in a few places. Let it sit 24 hours for the glue to set up. Put the door back on. You can put the door on immediately as long as you don't use the dryer for 24 hours. Easy.

1) removed the old broken filter
2) deposited it in nearby wastebasket (with lint attached)
3) used scissors (see above) to remove plastic cover from new lint filter
4) inserted new lint filter
5) marveled at my handiwork!

Changed out the lint filter

The dryer stopped heating, it would only blow cold air. I removed the back panel and tested the thermal fuse with a dmm. The fuse was open, so it was bad and I needed a new one. I tested the thermostat and the dmm measured continuity across the terminals, so I thought it was good, bad assumption. I ordered a thermal fuse from partsselect and it came with a thermostat. Like a dummy, I only installed the fuse. The 1st time I ran the dryer the fuse blew again, because the thermostat was bad. So, moral of the story, install both parts.

My dryer started squeaking and I thought it was the drum rollers, so I bought a set. When I attempted the repair and got as far as removing the dryer drum and I decided to spin the shaft on the motor and that was where the squealing was coming from. I put the rollers on and reassembled the dryer. One day later the motor seized up. Ordered a new motor and installed it with no problems. The nut on the back of the motor ended up being a 20mm wrench. Motor cost me $105.56 and the maintenance kit (ps37308) (2 rollers,4 clips, button clip, new idler pulley and belt) cost $32.08. It cost a total of $137.64 in repairs with no labor costs and I accomplished it in under an hour. Minor handyman skills needed or find a friend who is handy. My dryer is 14 years old and now is running like new again. I used the 50% rule, if a repair exceeds 50% of the cost of a new machine, replace it, if the repair can be done for less than 50% of the cost of a new on, fix it.