WSGX201HNA (ANSEEUS) LG Washer - Instructions

I followed a Repair Clinic Urube video except the video had a model with the controls in front and my dryer has the controls on a back panel. The difference was in how to get the top of the dryer off after removing all the screws. The video
said to push back on the top panel which did not work because of the back controls. Instead I had to push up on the front to release it and then push back. The rollers were also in a slightly different place but were easily found and replaced. The dryer is now back to normal.

I didn't get to do the repair because despite the model number and the picture being exactly what I needed I was shipped the wrong part and basically told by pets select to shake it off that's your problem not ours.

Could not do repair since the parts that I ordered were different from the picture on this site. I have emailed them to which they replied with one email asking for some info. I sent that to them and have not heard anything back in the last 3 weeks. I have even sent reminder emails and still nothing. I can't use my dryer due to damaging clothing and can't replace parts due to being the wrong part. Partselect is not very good at getting answers for their customers. Expert repair help is something i don't think they have. Getting some answers would go a long way but i feel like i have been left in the dark.

Following the reference video, step by step and taking progress photos along the way, organizing screws and hardware as they were removed.

The discrepancy I found was the new rollers that I received were complete with the shaft. The video with the older rollers instruct removing the rollers from the shaft.

To use the new rollers with the new shaft, requires removing an additional panel at both the front 2 and also the full back panel for the rear 2, to get a wrench on both ends of the shaft, and then attach the new roller bearing shaft assembly and re-install the panel.

Other than that, it went very smoothly and the result was a quiet rotating drum. No more thumping!

My dryer actually required 2 moisture sensors, but had only ordered one pack, which only came with 1 sensor. For whatever reason, I thought the pack would have had the 2 pieces.

Another reviewer made note to wear work gloves as some of the hardwares metal edges are quite sharp. Following that advice I completed the repair in 3 hours without a scratch. Thanks for the detailed video Partselect team and good luck to all attempting repairs.

Completly disassembled dryer removed 2 rear rollers installed 2 new rollers. Reassemble dryer in including new drum belt. Dryer is nice and quiet again running fantastic, thank you for your support

I'm not for reading instructions. So I just dove right in and took the dryer apart to get down to the motor. I gave the dryer a thorough cleaning and replaced the 3 parts I ordered from the online recommendation. Wish I would have ordered 2 sensors and the 2 thermostats that are near the burner. Just so replace beings I was in there. Replacing the parts was easy, found them just by looking for matches to the new parts. Reassembled the dryer, dont think I put a single screw back where I got it lol. And still haven't put the top lid back on due to difficulty. Not sure if I even needed any parts, found a nest in my outside vent completely plugging it. But after a good cleaning and replacing the parts the dryer dries the best it has since we've owned it. The dryer came with our house which we bought 3 years ago and it was 2 years old when we purchased the house, so it is now 5 years old.

Wife called me and said the washing machine just flooded the Landry room. I looked at it and didn't see anything wrong. Took the top off and the back off and started looking for a leak, did not see anything. Took the front part of the washer apart thinking the drain hole was plugged up where the rubber boot is. It was ok after taking the big rubber boot off or whatever that is called i was not getting anywhere. I put it back together left the top and the back off. I turned the water on and started the washer on a quick cycle looking for a leak. I found the bellows at the inlet had a small leak fixed that and started the washer again. So what i found out was the clean out drain plug was not in tight letting water out as it was washing after i tightened it all was ok. So i did find a leak that was small that we never saw. The hardest part was putting that wire clamp on the rubber boot it took two people to do that.

Able to complete install but the lint housing does not allow the lint screen to slide down completely due to the housing lacking the appropriate cut outs/notches. The slit becomes too narrow for the lint screen so it protrudes from the sides. The delivered product does not match the image on the item description, which shows the proper cut outs/notches that should fully accommodate the lint screen.
I'm having a similar experience with this reviewer:

John S - February 14, 2022
Verified Purchase
Lint screen housing
The housing will not allow the lint screen to set completely down because the housing lacks the proper cut outs causing the lint screen to set 1-1.5 inches too high. I was able to cut out the required notches in the plastic so that the lint screen would fit. The picture shows the proper notches but the delivered product didn’t have the notches and does not match the picture.

Will return the item and keep searching for the correct lint housing.

Removed top of dryer
I carefully removed wires from back of control panel
Removed control panel
Most of screws hold cabinet together
Unhook wire from light on door and sensor on the front panel.
Remove the front door and panel together
I changed both front rollers on front panel
If you have to change rear rollers lift tub up by belt
Remove screws on back of dryer that will let you lift out inside rear panel that holds the rear rollers
Change rollers and just revearse procedure to put back together

I did not do the repair I hired the propane company to do it . It was too difficult for me.they removed top & front of dryer .removed & replaced gas orfice reinstall all parts that were removed. Install and test dryer IT cost me $91.59 for labor & $24.65 for the part & shipping.If the dryer had a side access near the gas valve it could have saved me the cost of labor. I could have done it myself.

Handed the parts to my son-in-law he's very mechanically inclined had the job done in 20 minutes

I removed the Wire and spring from the tub seal and then removed the seal on the side of the washer that contains the Door switch. I removed the two screws that held the door switch in place while holding the switch with my other hand. Once the screws where out I pulled the switch assembly out thru the gap and removed the wires from old assembly. I then plugged the wires into the new assembly aligned the holes up and put the screws back in the new door switch assembly. I then put the door seal and tub seal holder back on. This took about 15 minutes. I do recomend that you unplug the washer before starting this process.

I followed the video instructions that were supply on your site

I took the dryer apart. You have to take the top off, then the door/front off. There are wires & other parts that need to be unhooked as well. A flat tip screw driver can be used to pop the top off. The screws were all phillips. Once you take that all apart, then you can access the drum. I bought the belt because I thought that was what was wrong with it. Turned out to be hair in the drum rollers. Took those all off & put wheel grease on each of them, put new belt on (since I had it LOL) then put it all back together. Make sure everything is lined up correctly otherwise you will have to take it apart & reline (which I had to do)
I am a 49yr old female & was able to do this repair on my own!

We replaced the drum belt and the rollers. Everything was very easy and straightforward but took a fair bit of time due to the extensive disassembly required. We followed the video available on the website for the belt replacement, which was very clear and accurate. Unfortunately, the rollers we received used a different attachment method than the OEM rollers which are depicted in the video provided. Instead of attaching from the front with a triangular plastic lock washer, they had to be attached via a nut on the back side of the roller. This required some improvisation and was a little more involved. For the rear rollers, we actually had to remove another panel to access the nuts, which was not described in the video. Nevertheless, we managed to get everything replaced and the dryer is working like it was the day we bought it.