WSGX201HNA (ANSEEUS) LG Washer - Overview

Diagrams for WSGX201HNA

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer Lint Filter – Part Number: ADQ56656401
$52.75
In Stock
Dryer Lint Filter
★★★★★
★★★★★
(38)
Part #ADQ56656401
The Dryer's Lint Filter is used to collect lint during the dryer cycle as it passes through the dryer vent, in order to prevent damage to the machine. This manufacturer-approved part comes in gray, measures around 12 inches wide by 11 inches high, and is easy to install. It slides into the lint filter slot in your dryer. If there is visible damage to the screen then it's time to replace the part. We recommend that you thoroughly clean the lint filter before every load, but even with good maintenance, this hard-working part is often damaged or worn over time. If your dryer isn't drying quickly, the filter may be responsible. The manufacturer has made an authorized substitution to the lint filter. Special details: When replacing lint screen ADQ56656401 you may need to also replace lint screen housing MCK49049101 and lint screen guide MEA49050001 to prevent items from catching on the lint screen, depending on your model.
4 PACK ROLLER ASSEMBLY – Part Number: 4581EL2002L
$141.66
In Stock
4 PACK ROLLER ASSEMBLY
★★★★★
★★★★★
(14)
Part #4581EL2002L
The drum support roller for your dryer holds the drum in place while the drum turns on the support wheels. The drum roller is round with a bearing in the middle and measures approximately 3 inches in diameter. If the dryer is noisy, won’t tumble, or takes too long to dry, you might need to replace the support roller. It is recommended that you replace both rollers at once. The bearing inside this roller is self-lubricating, so no grease will be required. Please remember to disconnect the power to your appliance before starting your repair. This is a genuine OEM part.
Lint Screen Housing – Part Number: MCK49049101
$61.55
In Stock
Lint Screen Housing
★★★★★
★★★★★
(2)
Part #MCK49049101
This is an authentic dryer lint filter cover sourced directly from the manufacturer. It protects the more delicate lint filter in your dryer, so that it doesn’t get damaged and lint can’t mix in with your clothes. This product is gray in color and is made of plastic. It is sold individually. The manufacturer has modified the part and suggests replacing the filter guide, part number MEA49050001 and the lint filter, part number ADQ56656403. The filter screen part#ADQ56656401 will have to be replaced as well.
Washer Hose with Bellows – Part Number: 4738ER1004B
$53.85
In Stock
Washer Hose with Bellows
★★★★★
★★★★★
(15)
Part #4738ER1004B
This washer hose with bellows, also known as a dispenser hose, is a genuine OEM replacement part for your washer. Replacing this part can be helpful if your washer is leaking. The dispenser hose connects the dispenser assembly to the tub. Before beginning the repair, unplug the washer and turn off the water supply. You will need a Phillips head screwdriver to complete this repair; a clamp tool can also be helpful. Remove the screws holding the lid of the washer in place, and take off the lid. Locate the dispenser hose and remove its clamps. Place the clamps on the new hose, using the arrows for a guide in positioning the clamps. Install the new hose and reassemble all other parts.
Moisture Sensor – Part Number: 6500EL3001A
$20.85
In Stock
Moisture Sensor
★★★★★
★★★★★
(3)
Part #6500EL3001A
The moisture sensor, also known as a humidity sensor, works in conjunction with your dryer by helping determine the amount of moisture in the drum to reduce overdrying. If the timer doesn’t advance correctly, it is suggested to check the moisture sensor bar for damage. A damaged sensor can cause the automatic drying cycle to not work properly and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting this repair.
Dryer Drum Belt – Part Number: 4400EL2001F
$72.55
In Stock
Dryer Drum Belt
★★★★★
★★★★★
(3)
Part #4400EL2001F
The drive belt is made to wrap around the drum, working with the tension pulley to rotate the drum. If your dryer drum will not turn, then you may need to replace your belt. This drive belt is 1/4-inch wide with 4 ribs and 3 grooves. It is recommended to disconnect the power to your dryer before you start your repair. This drive belt is a genuine OEM part.
Filter Guide – Part Number: MEA49050001
$54.95
In Stock
Filter Guide
Part #MEA49050001
This is a replacement lint screen guide for your dryer. The lint screen guide attaches to the front bulkhead and supports the lint screen. If your lint screen will not stay in place, or if you are noticing marks left on your clothes, a broken lint screen guide could be to blame. The lint screen guide is approximately 13 inches wide on its straight edge. It is made of plastic and is sold individually. This is an OEM part, directly from the manufacturer.
Clamp Assembly – Part Number: ACA56078801
$26.65
In Stock
Felt Seal – Part Number: 4036EL3001A
$52.75
In Stock
Blower Thermostat – Part Number: 6931EL3002M
$46.15
In Stock
Pulley Idle – Part Number: 4560EL3001A
$42.99
In Stock
Pulley Idle
Part #4560EL3001A
Washer Gasket – Part Number: MDS62058301
$41.75
In Stock
Washer Gasket
★★★★★
★★★★★
(2)
Part #MDS62058301
This part is the replacement rear tub gasket for your washer. It is made of black plastic and is approximately 3-1/4 inches in diameter. The rear tub gasket forms a watertight seal between the rear tub and the drive shaft. If the gasket is worn or damaged, it may not be able to create this seal, and you may experience a water leak from your washer. Be sure to disconnect the washer from the water and power sources before you begin this repair. This is an OEM part sourced directly from the manufacturer and it is sold individually.

Common Symptoms of the WSGX201HNA

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer making a thumping and squealing noise when running
132 of 171 people found this instruction helpful.
  • Mark from WAVERLY, OH
  • Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable), Wrench set
Had to replace front drum support rollers. Removed screws underneath top in back that held bracket that keeps top in place. Slid top towards rear and lifted up. Removed 4 screws that hold plastic front panel in place (inside..2 on each corner) Unplugged front panel electric plugs to remove panel. Opened door..removed 2 screws at bottom of door opening. Removed screws on top of front panel. Unplugged door switch plug. Removed front panel. Removed right front roller with 9/16th wrench for nut. Adjustable for back of stud. Lifted up on drum to get roller out. Reversed to install. Left roller a bit harder to get to stud. Removed and installed same as right side. Did not attempt to replace rear rollers. Have them if needed but very much more involved to replace.
Was this helpful?
Thank you for voting!
Screeching during operation
66 of 101 people found this instruction helpful.
  • CAROL from NAMPA, ID
  • Really Easy
  • More than 2 hours
  • Pliers, Screw drivers
Found disassembly video and watched several times. Suspected that one of the drum wheels had seized up. Found extreme volume of lint and hair inside unit as well as a dryer sheet melted on top of heating unit. Front left drum wheel was worn down from lint and hair jamming its movement. Video made it easy, not a really complicated piec e of machinery. Replaced all 4 wheels due to normal wear on other three. Wanted to be sure drum evenly balanced on all 4. Parts came quickly and were easy to install. My sister and I did this together. Would not recommend doing it alone. Took time to vac and wipe down entire unit. Now it runs so quiet we have to look to see if it is operating. Got a brand new machine out of it, saved a couple of hundred dollars in repair bills, and found 11 cents inside the machine. For your own piece of mind, if you have had your dryer for several years, you need to open it up and clean it out. Its not hard... added note, we are both in our 60's... so if we can do it so can you.... Such a feeling of accomplishment, can't buy that in a store....
Was this helpful?
Thank you for voting!
Filter parts chipped - replaced
52 of 92 people found this instruction helpful.
  • David from Annapolis, MD
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed existing parts using screwdriver, positioned new parts in dryer and re-inserted screws, tightened - done. Piece of cake, even for someone who cannot saw a straight line with a chop saw.
Was this helpful?
Thank you for voting!