WM2050CW (F1267FDY) LG Washer - Instructions

I followed the video. Everything worked exactly as described. i ran a quick cycle and everything seemed to be fine. Started a wash and the machine was going fine but stopped, and wouldn't drain. I thought that maybe it might be the Rotor Position Sensor assembly, which I had already purchased just in case.But first i drained the machine and checked out the pump filter. Plugged solid. I'm guessing when the pump went there must have been a lot of lint and debris in the machine. something you might want to check out, after that repair. Thanks. you guys saved me a couple of hundred dollars

First I had to elevate the washer on 3-5 gal. buckets in order to get underneath it and find the leak. Then I tried to repair the hose itself-which actually worked-but then the rest of the hose just started splitting everywhere I touched it. So I ordered the new part which took some careful comparing and examination online. But it was exactly the right part. You have to remove the top of the washer which is just 2 or 3 screws. Then taking the hose out was a little challenge-knowing I would have to put the new one back in carefully. Use Vaseline on rubber fitting at the end of the hose that connects to the washer. Need at least 2 people to raise the washer up in air to work on it.

In order to replace the bearings of a front loader LG Washer you will need to disassemble the entire unit. you should have excellent mechanical skills to tackle this project with necessary tools. Plan on replacing both bearings and rear seal, also plan on replacing the spider and drum seal. The Spider that supports the inner drum will be corroded due in part to seal failure. By the time you are hearing the bearing noise the damage to the spider will have taken place and need replacing. You can watch a few videos on youtube with similar appliances to give you an idea of the project at hand. Once disassembled cleaned and inspected the assembly goes real smooth. The washer now works as good as new and is ready for another 10+ years of service. Doing this project myself has saved me from buying a new one and that savings amounts to over $1000 bucks. LG washers are built to last and you will see that while working on it! Good Luck and do your homework!

Followed instructions on YouTube link. Replaced the shock absorber and washer is working really well.

With basic tools,the original drawer was broken up in tiny pieces and removed. The replacement drawer seems to have a little different design and doesn’t hang up internally.

just put new part in very simple only problem was shipping yall used fedex went to 4 states and one state twice they finally gave it to USPS so it took almost 9 days to get here

replaced switch as shown in the video...Worked great

I already had the top of the washer open, from previous disassembly to clean the front loader seal, and when I ran a trial load, noticed a small 1/4" tear in the hose bellows that attaches to the drum.

Very simple repair, remove the existing hose by loosening the clamps, paying attention to their orientation. Install the existing hose clamps onto the new hose, install and tighten the hose clamps.

5 minute job, if the washer top is off (which is also simple).

Could not do the repair. Partselect sent me the wrong parts even though I gave them the model number and the brand they sent me the wrong parts.

The repair went good but time consuming. I replaced both inner and outer tub bearings along with the tub seal. I removed top by removing two screws in back then pulling back slighty then lifting up. I removed soap tray by pressing down tab and pulling out. Loosened soap dispenser and folded back on top. I removed control panel then front door panel. Remove back panel. Remove motor and shocks and hanging springs which there are two. Disconnect the hoses attached to tub then pull the tub. Remove screws holding the tub halves together. Use punch to remove bearings. NOTE: If you put the bearings in the freezer prior to installing, they go in much easier. I used the old bearing, set it on the new bearing then I tapped the old bearing so not to damage new bearings. I replaced the seal then put everything back together. Not difficult but time consuming.

I removed the tub. Thin included disassembling the washer and disconnecting various hoses electrical connectors to facilitate the removal of the tub from the machine.
Once removed, I separated the two halves of the tub and removed the metal basket to gain access to the bearings and seal.
Removal of the bearings was much harder than expected as they were very difficult to drive out of their pressed in mounting.
I finally was able to remove the bearings and fabricated a press using a piece of all thread and two steel plates to install the new bearings and seal.
I would not attempt to do this again with the proper bearing pullers and an official press to install the bearings gently without beating the tub housing.
This repair I feel is beyond the scope of your average DIY. The bearings can be damaged easily without the specialized tools to install the components.

After I watched the repair video for the part, it was a snap. It went exactly as the video described the steps. Hardest part was moving the washer to get behind it.

Took off the old hose with a screwdriver and put the new one on. As simple as that. You don’t need a repair man to get this done, you can do it yourself and save money too.

It was giving me a code got on YouTube it gave the code after that bought a new pump and fix done

Replaced cold water inlet. Removed 4 water lines and 5 wires put new part in and reinstalled lines and wires