The drain pump and motor assembly may also be known as the washer drain pump and is a part for your washer. The drain pump helps expel water from the washing machine. The drain pump is activated after...
$109.04
In Stock
Order within the next 12 hrs and your part ships today!
This valve is used for cold water, bleach dispenser and prewash cycles. It has a standard hose fitting inlet with 2 outlets facing 45 degrees to the right and one outlet facing 45 degrees to the left.
$78.11
In Stock
Order within the next 12 hrs and your part ships today!
Also known as a door boot seal or bellow and comes with a drain hole. Door boot 4986ER0004F is an original equipment manufacturer (OEM) part that fits some front-load washers in these series: Kenmore ...
$143.63
In Stock
Order within the next 12 hrs and your part ships today!
This is a replacement sensor assembly for your washer. It may also be known as a motor rotor position sensor. The sensor assembly monitors the direction and speed of the spinning rotor and communicate...
$45.99
In Stock
Order within the next 12 hrs and your part ships today!
This washer hose with bellows, also known as a dispenser hose, is a genuine OEM replacement part for your washer. Replacing this part can be helpful if your washer is leaking. The dispenser hose conne...
$42.30
In Stock
Order within the next 12 hrs and your part ships today!
The tub bearing supports the spin basket shaft at the back of the washing tub. If your washing machine will not spin, is leaking water, or if there is a loud screeching noise during the wash cycle, th...
Order within the next 12 hrs and your part ships today!
Questions And Answers for WM2050CW
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mitch
July 6, 2021
Washer will not start power ls on
For model number WM2050CW
Hi Mitch,
Thank you for your question. If your washer will not start, there are some parts that you will need to check to see which one is causing the issue. You will need to check door lock assembly, the noise filter assembly and the rotor position sensor assembly. We hope this helps! Good luck with the repair!
(F1267FDY) or (ABWESED) Where are you getting this for part of the model number? I'm not finding it. I have installed two anti hammer/ shock absorbers on both hoses and better but still get hammering from machine when the valves close?
For model number WM2050CW
Hello William, thank you for contacting us. We would recommend checking the water valves, part number PS3527427, and part number PS11728995. These valves are the likely culprits of the issue and will fit your washer, model number WM2050CW (F1267FDY). Customer service is available 7 days a week if you need help placing an order. Glad to be of assistance!
Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer came apart quickly just moving down the front of the washer and removing the door, latch, tub gasket, drain cover. Removing the pump was just a mater of disconnecting the drain hoses, and one clip under the drain assembly. 3 screws attach the drain to assembly to the pump and only 2 wires that are clearly marked. Reassembly is just going back through in reverse order of disassenbly. The best thing about this is that it all comes apart with a standard phillips screwdriver.
I first tested the motor per the service manual. I checked the resistance between the terminals of the 3 pin connector. It's supposed to be 5-15 ohms. The motor checked out so I replaced the main electrical board. It turns out that wasn't the problem. After a brief web search I found out that the hall sensor (which is attached to the motor stator) was the likely cause of the failure. I replaced that and everything works great now. And now I have a spare main board in case that ever fails. I also want to mention that I took the time to remove the dispenser box (where the water comes in and is directed to the different cleaning products) and cleaned it with a very strong bleach solution. It got rid of the mildew and funky smell. It seems that the fabric softener caused a lot of mildew to form inside the dispenser directly above the fabric softener tray. The bleach took care of that. This is probably something that should be done routinely to keep the mildew from forming.
Thank you for the very helpful YouTube video. After watching the video, I was able to diagnose the problem, buy the part from your website, and complete the repair. This is my personal machine - I am not a professional repairman.
